4UP74 (Type 1) DeVilbiss Compressor - Parts

This is an OEM part sourced directly from the manufacturer. The adapter is designed for use in compressors from DeVilbiss, Black & Decker, Delta, and Porter Cable. This part is made of metal, and may be used to connect the regulator to the tank. You will require a wrench when replacing this part. This item is sold individually.

This replacement valve plate assembly is a high quality item designed for use on Craftsman air compressors. It is a genuine manufacturer sourced item that is used to control the airflow into the cylinder. Once the piston starts traveling up, the reeds on the valve plate open and air is sent into the air tank. Overtime the reeds will get w...Read moreorn eventually requiring valve plate replacement. One metal valve plate with reed valves and two rubber seals are included in this assembly. When replacing this valve plate assembly it is also a good time to replace the head gaskets which are sold separately. You will need a wrench set to complete this repair.

This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individu...Read moreally. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is a genuine OEM part. The Porter Cable nipple (1/4-18NPT X 1) is constructed of high-quality metal, and is compatible with many air compressors. This part secures the manifold to the compressor tank. An adjustable wrench set is helpful in making the repair. This part is sold individually.

It is an OEM component which is designed for use with air compressors. This special nut sleeve assembly secures the pressure relief tube to the pressure switch. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. One durable metal nut sleeve assembly is included. A wrench will be needed t...Read moreo perform this repair. Check the appropriate diagrams for your model to ensure the proper replacement procedure. Make sure to drain the air before starting this repair.

This is an authentic replacement part manufactured for use with Porter Cable air compressors. The safety valve is used to prevent the tank from overpressurizing by letting air out of the tank when a specific pressure is met. Safety valves have specific pressure tolerances specific to the model of air compressor it is important to match th...Read moree valve to your model of compressor. This safety valve is available as an individual replacement part.

This is a genuine replacement part manufactured for use with air compressors. This hex head screw has many applications from fastening the connecting rod, to securing the isolators. The screw is sold as an individual replacement part, please see model diagram for part location and usage.

This is a genuine replacement part sourced from the original manufacturer for use with generators and air compressors. The hex head screw is used with several different types of equipment and the application of the screw can vary based on the model of the machine. This screw is available as an individual replacement part.

This is an authentic manufacturer-sourced replacement o-ring which is specially designed for use with air compressors. It helps to provide an air tight seal for the nut which secures the outlet tube, please make sure to check appropriate diagrams of your model for correct location and use of this item. Over time o-rings tend to deteriorat...Read moree and crack eventually requiring replacement to maintain the proper seal. Note it is a high-quality component which is made of durable rubber material and it is sold individually.

This is an authentic replacement part that has been OEM sourced to be used with Porter Cable, DeVilbiss, and Black and Decker air compressors. The metal nut is commonly used to connect the outlet tube to the cylinder head assembly. This item is available as an individual replacement part, a hex wrench is needed for this repair.