4KMEDX505BW0 Dryer - Instructions

I first went to your site and studied the parts diagram to see where the element was located. I then unplugged the dryer and pulled from the wall. After that I popped open the front cover and accessed the bottom of the dryer where the element was located. I then removed two screws that held the element in place and removed the wires to the element. After a little tug the old element came out. I slid the new one in place and connected the wiring and screws and replaced the cover and pluged it in. Works good as new...

It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum back in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone

Removed old filter and put in new one.

Took off the top and front panel. Found that the belt tensioner was worn out. Decided to pull drum out,and replace the belt and drum rollers also. Put it back together, and it works fine.

Following the very helpful instructions that I found at PartSelect.com I was able to open the dryer and access the heating element which I suspected was bad. I realized later that I didn't need to open up as much as I did but the job was easy. In the future I would only open the panel below the door to access the element.

Just to make sure that it wasn't a problem with a thermostat or thermal fuse I also checked continuity from the temperature selector knob on the control panel to the heating element. When I verified continuity (zero resistance) I knew that the element was bad. Once I removed it I could see that one of the coils was broken and I should have just checked that first and not bothered opening up the control panel at the top.

Still it was less than an hour of work total. I have some experience with DIY projects but have not worked on appliances before. Thanks for the great site with good instructions and lower costs than the local parts counter.

Replaced the belt and the wheels supplied with the kit. I also cleaned the inside of the unit. It looks and works like new.

1st. i removed the two screws that holds the cover.
2nd. -vacumn (most time used)around to find the screws that hold the metal heat tube and shield.
3 rd. removing the screws tip the front of the tube up and pull out from the back.my element was clipped in place. I then pulled the element out and replaced the thermostat (tip: replace all t'stats around the heat element). it is as simple as reading the repair stories

It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.

Replaced

First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.

Well I unplugged the dryer, then I removed all the screws off the back of the main console. After that I unscrewed the old timer. Then I one by one moved the wires from the old timer control to the new timer control. Then i screwed in the new timer control. After that I screwed the back plate for the main console back on. And finally I plugged the dryer back in. And there you go it was that easy.


I also wanted to say that this experience with parts select was most amazing one too. I ordered the part one day with a 3 to 5 day delevery time. The following day I checked on the status and found out that the part would be here the next day so I was really amazed that it would be that quick. I would recommend and would come back to parts select for futuer needs for appliance parts.

First i tested each part for continuity and found out that the thermal fuse was bad. So ordered the part and went ahead and got thermostat and element to ensure no problems in the future since I already was in there.

I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.

the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.

First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Piece of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!