All Installation Instructions for Maytag Range 4KAER5500AW1

Glass door front fell out during cleaning and shattered

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great

Parts Used:

Range Exterior Door Glass (White)

Range Trim Lower (White)

Dennis from Ft Myers, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

broken outer range door glass

Using 4 strips of duct tape was useful,in holding the glass to the door.

Parts Used:

Range Exterior Door Glass (White)

Thaddeus from Washington, DC
Difficulty Level:
Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

I had a power serge and it burned the Plug at the termial block and melted a few wire.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Parts Used:

Range Terminal Block

Robin from Vanderbilt, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

stove top got hot when using large pans

Removed the existing element and replaced it with the new one.

Parts Used:

Delta Frame Canning Element - 8"

Albert from Bryant, SD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Side trim broke

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

Parts Used:

Side Trim - Right Hand Side

Paul from Adamsville, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Parts Used:

Oven Sensor

Dave from Titusville, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

8 Inch electric burner not getting hot

I determined the problem by swapping the 8 inch burner with a 6 inch burner. the 8 inch got hot when connected to the 6 inch wire harness. This told me that the 8 inch burner was good. The 6 inch failed to get hot so I determined the next logical thing was the power to the 8 inch burner. I used a multi meter to determine that power was getting into the control unit but no voltage was getting out. The controller was bad. I ordered a new controller and after unplugging the stove, replaced the controller in about 10 minutes. (Critical part of repair is to unplug unit from wall -220 volts!)

Parts Used:

Infinite Switch - 8 Inch

John from Dover, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Stove kept turning off

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Parts Used:

Oven Sensor

Richard from Wooster, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Replace bowls

Removed old bowls and replaced with new ones. Easy. Piece of cake. Perfect fit.thanks.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Judy from Indianapolis, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner stopped heating up.

Searched the internet for the replacement part, placed the order and then disconnected the old one and inserted the new burner prongs into the socket. Worked perfectly!!!

Parts Used:

Surface Burner - 8 Inch - 2600W

Robin from Chicago, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven shutting off after temp reached 350

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Parts Used:

Oven Sensor

Ken from Las Cruces, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

bowls had burnt on food

replaced them

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

David from Saranac Lake, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner no longer connected with electric power source

I had determined that the the burner itself was no longer capable of connecting because when I removed another burner and inserted it, it worked just fine. Also, the defective burner had not worked when inserted into another outlet. I was delighted to be able to purchase a replacement so quickly and easily on my own, without having to call a repair person or seek a retail outlet.

Parts Used: