4GMVWC300YW2 Maytag Washer - Instructions

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!

I needed an air impact wrench to remove the single nut. It was stuck on there. Once the Nut. Was removed it was an easy repair. Perfect fit! Just pop it on the shaft and replace the bolt. Since I had my air tools out already I gave it a couple of dugga duggas.

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!

I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.

Just follow the video! Very easy.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Replaced agitator sprage kit. Simple instructions simple repair

The old part popped right off, and new one installed. Works Great!!!

The info. was really helpful

I used a jack to lift the tub and unhooked the rods and replaced them. Works great.

Gravy replacement! I pulled out softner dispenser,
undid the one bolt securing the agitator assembly, and removed the top half of the agitator. the cam assembly tapped out. I replaced the bolt so I could still use the machine while the parts were on the way. When the part arrived (36 hours later with 3-5 days expected) I removed the bolt again and followed the simple instructions to replace the cam. Saved a ton on repair costs!

I am a maintenance mechanic and was very easy for me. I just loose i screw 10mm took out old parts put new parts in and it was ready to go again.

I removed the fabric softener dispenser atop the agitator. I twisted and pulled out the plug inside the agitator. Using a socket on an extended wrench, I removed the single nut inside the agitator (keep the agitator from turning with a large screwdriver, etc. and turn the nut counter-clockwise to remove). The agitator came out, and I removed all of the cam parts. I cleaned all of the old parts with bleach and water. Reinstalling the new parts was simple and straightforward as indicated in the illustrated instructions. Now it works great!

I popped the cap off the agitator removed a bolt. Removed the damaged parts. And replaced them with the new ones it was easy.