48231010108 (WM2601HR /00) LG Washer - Instructions

removed 2 screws on back. removed top. disconected wires and hoses removes 2 screws holding assy in place and removed assy. put in new assy and installed hoses and plugs in same location removed from. reinstalled top and hose and ran washer.. new valve unite works but has a high pitched whine when valves turn on. :(

I unplugged the washer, and removed the top of the washer by removing the two screws securing the top to the washer. You'll find them inside the two plastic pieces on the rear of the top. Remove only the bottom two screws in each plastic piece and slide the lid to the rear a few inches then lift straight up to remove the lid. Disconnect the water hose from the rear of the inlet valve assembly then remove the two screws in the rear of the old water valve bracket that attach it to the washer. Pull the old unit inside the washer and set the new unit on top of the old. Swap over the electrical connections to the new water valve assembly, matching the locations where the connectors were originally. Then swapped over the water lines from the old unit to the new unit using common pliers to compress the hose claps. Finally, attach the new unit to the washer with the two rear screws. Replace the water hose and the top, and the unit is ready to test.

Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring harness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phillips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

the best video was on you tube and showed exactly how to repair my washer. the parts arrived quickly and was a perfect match. thanks for helping me save some moola and making mama happy.

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

found a slow leak in one of the valve seat gaskets and decided to replace the entire valve (also did the hot inlet as well just in case). Unplugged unit, detached water hoses (replaced these as well), moved the washer out about 12" from the wall. With Phillips head removed the washer top. With pliers removed the hose clamps off the valve heading to the detergent dispenser (be sure to keep track of what hose goes to what nipple). Detached electric clip from each solenoid. Using Phillips head removed the valve. Use reverse order to install new valve. Ran the unit through a long cycle with the top off to ensure there were no leaks.

unplug washer and disconnect inlet and outlet hoses. drain water from washer (about 2 gallons) by removing lint screen from front of washer. lay washer on side (I used a blanket to avoid damaging the paint) remove all the phillips head screws in the plastic bottom and the metal feet of the washer. Gently pull the bottom of the washer off. There are 3 shock absorber looking things that pull apart and are greasy. Try not to mess with them much. Just pull gently, and they slide apart. cut the zip ties holding the wires to the washer bottom piece. remove the screw in the lint screen area and gently pull the recessed plastic thing out the front of the washer. remove the screws holding the pump assembly on the front of the washer. Remove the three screws holding the pump assembly on the outlet pipe manifold. Installation is the reverse of removal, take care to put the shock absorber looking things back in gently and together at the same time when reinstalling the plastic bottom of the washer.

Our washer and dryer was stacked, and had to remove the dryer to access top of washer. This took 2 people and was not difficult due to the 168 lb weight of the dryer. Turned of water, pulled washer away from wall and disconnected the supply hoses. Removed the 2 screws holding the top, slipped it back and removed. Removed the 2 screws holding the inlet valve assembly, unplugged the wiring harness from the 3 solenoids, disconnected the 3 hoses from the hose bibs on the valves. Mounted new valve assembly, connected hoses making sure that clamps did not touch any other hoses, reconnected wiring harness, turned on water to check for any leaks, put top back on and tried washer out. Changing the valve assembly took a total of 15 minutes. Really simple. The You tube video very helpful in determining how to do the job.

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

I took the back panel off the washer and located where the leak was coming from. It was obviously coming from around where the cold water hose connects. Checked washers in hoses and they were good. Noticed a small drip on the valve assembly that the hose connects too. Took off small panel where the hose connections are mounted....disconnected all 3 black water hoses that connect to it (squeeze metal clamps with pliers and slide hoses off. and numbered them with permanent marker so I wouldn't get my lines crossed later), removed the quick disconnect electrical lines.... removed part and googled the parts diagram on this site.....identified the part in the pic and ordered....it was here in less than 48 hrs with the basic shipping (which stated 3-5 days:)....reassembled the same way I took it apart. I'm prud of myself, it was pretty easy and I'm sure it saved me a lot of money!:)l

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

removed dryer which was stacked on top of dryer. opened washer top by removing screws from plastic hold down parts on rear. replaced valves with new valves you all sent me. reassembled and restacked dryer on washer