41797812702 Kenmore Washer Dryer Combo - Instructions

Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

I used a screwdriver to remove the front of the washing machine, fit the belt around the main pulley, held in the spring loaded tension pulley, and threaded the belt aound. It works great! I really need this inexpensive repair, since my job was downsized, and I can't afford to pay anyone.

unplug dryer. lift the top of the dryer up and back. Take the screws out holding the front panel on. One on each side. Disconnect wires from door open stop switch and take front panel off. Remove drive belt from around pulleys and lift drum up and forward out the front of the dryer. I had to replace the plastic and metal holder and the grounding ball also. Remove the shaft from the drum and put he new one on. Put the drum back in, wrap the belt around the drum and set drum in plastic holder. Then just reverse your steps. Fairly easy.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

The repair went very smoothly. I'm a woman in my mid 20's and was prepared to buy a new dryer but I saw the part online for a very reasonable price and the video instructions were extremely helpful. I was able to fix the dryer quickly and cost effectively AND the part arrived in only 2 days! It all worked out very well.

Unplug, lift top, unplug 5 wires, remove 2 screws, pull dryer front away while supporting drum. Remove old glides, snap in new. Reverse disassembly procedure

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

screwed in the new legs and leveled it off again.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

Disconect power, Removed top and front of dryer.
The broken zipper was easly removed at this point. The plastic glides easly snap out and in. The felt took some more time to scrape off and clean the old glue. Glue the new felt into place and replace front and top. The parts were shiped promptly and the dryer was out of service for only three days.

Removed old guides ( some of the snap in fastners were broken off). REplaced guides by rolling drum, easy to snap in @ drum bottom each time.

Removed old filter, installed new filter

watched video on replacing rear bearing.although rear bearing was not the part(s) i needed to replace, video instructed disassembly procedures to get to the drum glides. this was a very simple and easy to follow video. repair was a breezeand took roughly 25 minutes. the most time consuming segement of repair was vaccuuming out lint,that was 15 minutes. In future, as a preventative, i plan to remove front of machine to clean annually.
Thank you.