41790807990 Kenmore Washer Dryer Combo - Instructions

It turned out that the pump was fine. There is a filter within the rubber bellows between the washer drum and the motor. You need to remove the entire bellows to get to it. Just remove the motor and you can un-clip the hose tensioners. They are exactly like the ones you would fine on most foreign cars - just compress with pliers and m ... Read more ove back on the hose. Clean out the plastic filter. A small nail had worked its way through the plastic filter and lodged in the motor impeller. Removing this nail and reassembling, it all worked as new! I kept the pump and motor as a future spare rather than return it.

5 mins. Take off fabric dispenser. Pop off cover underneath. Unscrew bolt. Pop off agitator. Put on new one. Screw back down. DONE :0)

after removing the panel covering the dryer blower and removing the blower cover, i pulled the old blower wheel off and placed the new whell on carefully lining the flat edge of the wheel hole up with the flat edge on the blower piston, the n i placed the clamp on and put back all the housing covers and panels...and now my dryer runs quie ... Read more t and drys cloths fast....thanks to partselect!!!!

remove side panel & start rinse cycle & heard a grinding noise in discharge pump. used a bucket to catch water upon removeal of discharge hose to pump. unplug disconnect plug to motor, remove pump from unit. Discovered propeller was loose in housing. Googled Partselect.com, odered part & in 2 days later installed new pump on unit. Started ... Read more a load of wash & it has been working perfect ever since. thanks to PartSelect.com for the service, the repair was minimal & easy for the DO IT YOURSELFER. Bill Starry

Once I figured out that it would not spin because it did not drain. Unplug machine and remove the back pannel. Locate the drain pump on the bottom of machine. Remove the power wires and the screws holding it to the bottom. Then use a pliers to remove the hose clamps ( was easer for me to tip the machine forward ). Be prepaired to catch or ... Read more soak up extra water from lines. The hardest part to the install is the limited room you have to work with. Install screws to hold the pump in place then install water lines, power wires and back pannel. Only thing left is to plug it in and watch for leaks.

My Husband did the repair it took less than 15 minutes. He popped the front off the washer. He then unscrewed two screws and removed the pump assembly. He popped the new pump in, and put in the tow screws. Then he put the washer front back on replacing two screws. It took all of five minutes. I am so pleased it was so easy. I told him nex ... Read more t time I'd do the repair and he could watch!
Lil

I got online and found that everyone was charging a king's ransom for a piece of plastic. Your ransom was slightly less. Then I paid $7 shipping and handling for the part which came packed in a box six times its size...I guess all that cardboard costs a mint. I opened the box, removed the lint filter, and put it into my dryer....voila! ... Read more No more holes!

first removed the 2 screws disconected the terminals, installed new switch connected wires back and test washer and it worked like new, i put a Jumper to get the washer to work while i got the parts. Also i received the parts in 24 hrs. Thank You.

i took out the two back screws lift the top.
took the two bottom front screws , lifted andtook off the front panel.took off the old belt an intall the new one in a circular motion put the panel and top back on and done.

First pry up on the front edge of the top panel of the dryer which is held in place by snap in clips. Pivot the top open and support against wall or other taking care not to pull on wiring harness. Next remove the 2 screws that hold the front panel in place. These are located on the inside of the front panel. The front then snaps loose al ... Read more so. Remove the plastic drum stop located at the top edge of the front of the dryer. Next I removed the 3 drum screws located inside at the back center of the dryer. Next you can you need to remove the belt the motor located at the rear vent panel on the back. Slide the now loose drum out exposing the rear bearing. With a 5/16 end wrench, loosen the 2 screws on either side of the bearing retainer. Assemble the new bearing bracket to match the old one. Apply a liberal amount of supplied lubricant to the pivot ball and plastic retainer. At this point it was helpful to have someone at the rear of the dryer hold the new retainer bracket against the back of the dryer while I tightened the new bearing assembly in. Assemble dryer in reverse.

I removed the bolt holding the agitator in the tub and lifted the agitator out. There seemed to be a part near the top that was not engaging. I decided to order a replacement to see if that was the problem (my local repairman had guessed the problem was in the transmission and said I should just replace the machine.) I ordered the part on ... Read more line and it arrived in only two days. I was very happily surprised by the speed with which I received the part. I put the new agitator in, tightened the bolt and ran a load of clothes. All worked perfectly

Received lid lock within 24 hours, fixed washer within 10 minutes...up and running. Thanks.

After turning the water off and removing the hoses,I pulled the top off by removing the 2 screws from the clips in the back and popping the 2 spring clips in the front. I then removed the 2 side screws left and right to allow room for the sides to move out of the way of the motor. The back panel is spot welded so the panels stayed connect ... Read more ed. I then removed the 2 screws from the water overflow guard on the motor. Once removed I unplugged the wire harness from the motor. After that the 4 nuts were taken off of the bottom of the motor. I pushed the belt tensioner in and pulled the motor out. Install the motor making sure the nuts are tight as they can work loose from vibration.

Removed 2 screws at bottom of the front panel - removed front panel by sliding the panel down about 1/2 inch and then away from the appliance- v belt is removed by pushing the tensioner pulley to remove tension from the belt and turning the pulley untill the belt is removed instalation is a simple reverse of the process. I did't have a ... Read more repair manual so every step was trial and error untill I was able to complete the repair.

First I removed the front panel,then set the timer to run. It began the drain,spin cycle, pump ran, but no water went out. Shop-vac the water out,removed hoses from pump,took out mounting screws from base, unplug pump plug. check hoses for debris since they're open, the impeller was broken. ordered the part . Mount the pump to the base, ... Read more put the hoses on, plug in motor and replace front panel. plug into wall