41748116700 Kenmore Washer - Instructions

I had called a repair man; and fortunately he never returned my call. After reading many of the reviews involved with the same problem, and wanting to use my washer, I decided it was easy enough to give it a try. And so it was. 2 screws in back removed the cover; and 2 screws in the front of the washer permitted the removal of the affected part. Removed three "plugs" from old; put them on the new part; replaced it back in the washer, and replaced the two front screws, which held it in place. Replaced top, securing with the two screws. And surprise - surprise -- the washing machine was working again! Your reviews were so helpful and encouraging --- that this really old lady decided to try it --- and like they all said "It was really easy to fix."

(1) Removed top of washer . (2) Open washer door . (3) Removed the two screws holding the Door Lock Sw while holding the switch from inside the machine . (4) Lifted the switch up to remove wire harness one wire at a time and reconnect to new switch . Double checked work and reinstalled switch . (5) Run washer machine make sure everything is back working . I need to add that the washer door needed to be adjusted . The bottom of the door was kicked out . Washer is now working .

Despite putting all the information about my washer in the order, I received a dispenser drawer that was similar to the one I needed, but would not fit. It was also a slightly different color than the original part on my machine, so obviously someone just threw it in a box and sent it to me. It wasn’t even wrapped in plastic! Just the part in a box, no instructions, no bill of sale, nothing. When I needed to return it because it wasn’t the proper part, I HAD TO PAY THE $10.00 TO SHIP IT BACK!!! Really poor customer service in my opinion. Hopefully I will at least get a credit for the incorrect part that I had to pay to return.

Disconnect power. Disconnect water hoses. Remove back panel. Remove top panel. Disconnect bladder ring. Disconnect control panel wire harness and control panel. Remove front panel. Disconnect hose clamps to drain hose and tub drain hose. Disconnect pump motor power supply wire. Disconnect pump screws. Now do everything in reverse replacing old pump with new.. One special note: replace factory hose clamps with new hose clamps.

By unscrew the washer Machine door off' then place the door flat surface and start to unscrewed each screw carefully keep all the screws together then remove the broken glass that you don't cut yourself in a safe place, then place the New glass back on & replaced all the screws back on tightly once all the screws back in then replaced it back on to the washer Machine, make sure you pre-test your washer Machine for no leaks.

Took the old one off and snapped in the new one.

Removed broken Vane and reinstalled replacemnet real time repair 2 minutes. It took longer to open box than to fix.

Inserted new vane into slots in the drum. I then held the front of the drum while I slid the vane tabs in place by pushing the vane to the back of the drum. Once the vane was in place, I screwed in the screw that came inside the vane kit.

I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

Unscrewed the old striker and screwed in the new one.

The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installation for DIY. The new legs work great.

pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...

I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.

Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!

After making sure there was no blockages and the pump was not jammed I knew it was time for a new one . Unplug the machine and turn off the hot and cold water . Remove the two screws on the bottom of the front of the machine and push down on the panel it should come right off . Make sure all the water is drained out of the tub use a wet/dry vacuum to suck out all the water if needed . Then with the vacuum empty squeeze the clamps that hold the hoses on the pump and push them out of the way . Use the vacuum to suck up any leftover water, as you remove both hoses . Unplug the one set of wires going to the pump . Remove both screws and the pump should now be loose . Do the same thing in reverse to install the new pump . Other than dealing with the water it should take under 15 minutes . Good Luck