41729022890 Kenmore Washer - Instructions

It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!

First I tried to unscrew the two screws holding the latch with a phillips screwdriver. When it wanted to slip, I took a closer look at the screw heads and saw they were square drive. I got the proper tool and removed the screws, replaced the latch and replaced the screws in a few minutes.

I push the new knob onto the post that fit the knob

pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...

Pump replacement quite simple - most difficult part of job was figuring out how to disassemble outer washing machine panels. Pump required disconnecting 2 hoses and an electrical connection.

the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.

"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be dis ... Read more connected to get access to the top pin. If I had to do this again it would take about an hour.

The local appliance repair store quoted me $80+ for a "kit" to repair the door catch. I saw the part on your website for less than $8. Even with rushed shipping (I have four boys who generate lots of laundry), it was only about $20 total. You guys are AWESOME! I sell tools for women and do-it-yourselfers and am directing my customers ... Read more to your site. Thank you!!!

It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.

Disconnected power, removed hoses, removed housing and pump. Re oriented drain pipes on pump to align with washer hoses (just twist collar and re set) attach foot bracket and secure to washer bottom. Attaching the hoses with the compression clamps was a bit of a problem until I used pliers to press the ends together and then an adjustab ... Read more le wrench to hold them tight. Slid on hoses and released clamps. Replaced electrical and secured pump cover. Done in about 15 minutes.

remove one hose clamp.pulled hose from back of washer.replaced with new hose in same procedure.best of all i had my new hose in two days.great serviceand inventory.

Loosened top of washer from spring tabs and leaned it against wall, removed two phillip head screws from the front bottom panel, removed panel. Removed spring clamps from 2 hoses( make sure water is drained from tub before doing this!!) on pump, removed 2 wire connectors. Used nutdriver to remove 2 screws that held down pump. Replaced pum ... Read more p and everything else installs in reverse. Almost forgot, the plate that holds the pump to the bottom of the washing machine has to be removed from the old pump and attached to the new one.

The wind blew the washing machine door shut so hard that the catch snapped in half. I found Part Select dot com on the internet, ordered the part and within a couple of days, it arrived. I didn't even do the repair...my Fiancé did it while I was away at a conference. Easy to fix, great ease of finding the part on Part Select...saved th ... Read more e labor of having a repairman come out to fix it. When in doubt, Do It Yourself!

First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cov ... Read more er and two srews as well.

PartSelect is fantastic. Door catch broke on 3 day holiday weekend and given age of washer figured nobody would have the parts. Found PartSelect on line, ordered, paid for expedited shipping, got the part by the end of the week. Took me just a few minutes to screw in the catch and I was doing laundry again the same day. Had a little bi ... Read more t of a problem identifying the part on the schematics but once I figured it out everything was a breeze. Recommend PartSelect highly.