4071110 General Electric Dishwasher - Instructions

I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.

The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.

So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!

I removed the anchor screws at the top of the dishwasher, and the screws holding the bottom kickplate in place. I pulled out the dishwasher 8-10 inches to expose the cables where the plastic hinge arm links are installed.
On mine, there is a steel cable with a hook crimped on the end. The hinge arm link doesn't slide out of this crimped hook easily as-is, the opening is too small. I removed the old link pieces by breaking them, but I couldn't get the new hinge arm links installed without filing the opening of the hook to accept them more easily.
The demo installation video doesn't show this spring-cable-hook-hinge link configuration, so it was a little more involved than I expected. I would have packed my metal file if I had known this would be an issue. I replaced both sides while I was in there, and the remaining good one was pretty brittle. I was glad I took the time to do both. I had to file both sides to install the new links.

The dishrack rollers were easy to install.
The rack slide end caps from the factory were difficult to remove and reinstall without some pliers and elbow grease. The replacement part was much easier to install.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

flapper then bought the spring

Popped out Old Roller, put in new one, pushing it together with a pair of pliers.

My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item

Check all your rollers before you buy just one!!!!!

The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.

Removed rack, removed old roller pieces, installed new, replaced rack , and works as new now!!

Although the replacement part was different that the original, the replacement is a better design and attached with no difficulty.

No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!

Repaired the soap dispenser.