4070810 General Electric Dishwasher - Parts

If your dishwasher door will not close, is noisy when operating, or the dishes are not cleaning properly, you might need to replace one or more of the wheels. Each wheel and axle are made of plastic and fit into one another so they can be clipped on to the lower dishwasher rack.

The Rack Slide End Cap is a white one-inch plastic part which replaces the end cap for your dishwasher rack, preventing your rack from sliding too far. If you find the dish rack is causing the door to not close properly, it may be due to the part being worn out or damaged. All you need to complete this repair is a small flat blade screw d...Read moreriver. Simply pop out the cap with a smaller flat-blade screwdriver and snap the new one into place. If the rear cap needs to be replaced you will need to remove both front caps and slide the rack completely off for full access. It is important to note that this part is sold individually, and more than one may be required, depending on your repair. An inexpensive part, it can be a good idea to purchase several at a time to have on-hand when needed.

The lower spray arm is mounted to the bottom of your dishwasher tub, and it rotates and sprays water to clean the dishes in the lower dish rack. This spray arm is made of gray plastic, and is approximately 20 inches in width. The lower spray arm will not spin if it has become clogged with debris and hard water deposits from your dishwashe...Read morer, if it has become jammed by silverware, causing it to melt, or if the bottom of the spray arm has become disconnected from the bottom of the tub. If the spray arm encounters any of these issues, it will need to be replaced. To replace the spray arm, remove the lower dish rack and simply unscrew the old arm. Screw the new spray arm in until it locks into place.

This is a basket for washing flatware or silverware in your dishwasher.

The circulation pump adapter, or pump adapter assembly connects the circulation pump to the tub of your dishwasher. If your dishwasher is leaking around this adapter, check the connection to ensure everything is fitted tightly. If there is a problem with the adapter, make sure to disconnect the water supply to your dishwasher before completing the repair.

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. This valve has a 3/8" inlet and comes with the mounting bracket.

This is a handle actuator for your dishwasher. It is made of black plastic, and is sold individually. The handle actuator is found in the control panel, and it releases the door latch when you lift the handle. If your current handle actuator is cracked or broken, you may not be able to open your dishwasher door, or the door will not close...Read more properly. The dishwasher also may not be able to start, and if this is the case, you will need to replace this part.

This switch interlock is found on your dishwasher door, and it must be actuated for the dishwasher to start. If your dishwasher door does not close properly, or if the machine will not start, you may have a problem with your switch interlock. This part is sold individually and is an OEM part, built specifically by the manufacturer.

This filter sits at the bottom of the dishwasher.

This is the replacement fine filter hub nut for your dishwasher. It is made of white plastic and is approximately 3 inches in diameter. The fine filter hub nut is also known as the lower spray arm hub nut, and it connects the lower spray arm to the hub. If the hub nut breaks, it can cause the spray arm to wobble during operation and this ...Read morecan result in a strange noise. To replace this part, first remove the spray arm by turning it counter clockwise, then do the same with the hub nut. Install the new hub nut by turning it counter clockwise, then replace the lower spray arm. This part is sold individually and is an OEM part from the manufacturer.

Your dishwasher’s middle spray arm is connected to the top dish rack, and moves the water around to clean the dishes. If your dishwasher is noisy, or it is not cleaning the dishes properly, you may need to replace the middle spray arm. You should also replace the part if the holes on the spray arm are clogged, or the arm itself is cracked...Read more or broken. To replace the middle spray arm, simply unscrew the old spray arm and screw in the new one. This part is sold individually and is made of white plastic. It is approximately 20 inches in width.

This part allows the water to flow in the drain direction only and prevents the dirty water from coming back into the tub.