404714 General Electric Dishwasher - Instructions

Rather than remove the dishwasher from the counter, I performed the repair inplace, which was much less work (although I did have to lay on the floor).
After turning off the power, I removed the two access panels at the bottom of the unit, disconnected the wiring from the pump and solenoid, loosened the drain hose fitting and drained most of the water out of the unit and into a shallow pan (the drain solenoid was stuck open, so this was pretty easy - otherwise, I still could have manually actuated the drain valve & solenoid to drain water through this hose).
There was alot of water in the unit and my pan overflowed a little. If I was doing this again, think I would have disconnected the drain hose from under the sink and drained out through that into a bucket (I could have controlled that flow better).
Once the water was out, there are just two hose clamps that hold the pump onto the unit (one on top and one in the back), and a stabilizer bar that connects the motor to the front frame. Removed these and the whole unit came right out.
The replacement pump & motor was exactly the same as the one that came out, so I didn't need any of the hose or wire adapters that came in the kit.
Reconnected the two pump connections, motor bracket and wiring, and the unit was good-to-go!

bottom rack was easy as just pull out and replace. Upper rack had to move front part of the brackets to pull out rack which did require some figuring out but I did finally get it and once I figured out one side the other was easy.

Replacing the rack was a "no-brainer". I simply removed the plastic keepers on the ends of the roller racks with a screw driver, pulled the old one out, slid the new one in, and then replaced the keepers with pliers. It couldn't have been easier.

If you are replacing an overheated solenoid that had the plastic melt, don't forgot to order a armature and link as well. I made this mistake and had to wait another week to fix the dishwasher. The repair wasn't too bad. The most time consuming part was putting the E-clip retainer ring back on the diverter shaft. Tipping the dishwasher back some really helped for me to have more room to see and work with.

Our older dishwasher would get hung up and not proceed to its next wash cycle. I removed the power to the unit took it apart to inspect. I figured it was somthing to do with the timer. I unhooked the power connection to the motor for the timer. I then plugged the unit back in and checked voltage to the timer motor. I had power at the connection. I then plugged the connection back into the timer motor. The timer motor still did not function. I went online looking for parts and found this site www.partselect.com. All the parts needed to make repairs were listed and good pictures showing the parts I needed. The part was recived a couple days later. I installed the new timer plugged the unit it and it works great now. I even purched a couple other parts to make the unit good as new.

Removed bottom tray from the dishwasher and in the back there is a screen with 5 hex head screws. Removed the screws and then lifted the screen out to expose the vavle. Unscrewed the valve by hand an installed the new one,hand tighten only. Reversed order for reassembly.

First shut off the Power and Water to Dishwasher, removed from under counter, removed sump screen and retaining clamp from sump housing and then loosened seal from inside dishwasher cavity. Upon removal I went in search of a replacement part and found Parts Select on the web, entered my model and make at there web site and found the part I needed, I could verify the size by the easy picture on a one inch tile background for the dimenision . I called in the order since I wanted overnight service, I received the part and after cleaning the area where it goes I proceded to put things back together, this took about a hour and a half and the dishwasher is back in service

I ordered parts before opening. My theory was to have the parts so that the dishwasher was not apart for longer than necessary, in the hope of avoiding the wrath of momma bear who just wants a new one... Once I opened up the door I realized the spring for the main lever arm had broken its mount. I drilled a new hole and reattached the spring. I did not need any parts. However, the original parts corresponding to the three parts I ordered were all beat up and brittle, so I was happy to replace anyway. I did not even explain, she is happy the cup looks new and is happy with the dishwasher. It even says Cascade on it, almost like an upgrade :). If your cup does not latch I would order the three parts I did and also order the lever spring. It was very corroded after 30 years, so I would have replaced if I purchased it. Next time.. :)

Actually, the problem started with a Timer Motor failure, and that let the dishwasher run for 4 hours (doh!). Immediately, I tested and ordered the timer, which unfortunately didn't come as just a motor, it came as an assembly. I installed it, and the dishwasher ran the cycle just fine.

Except it didn't drain.

After poking around, I noticed the drain solenoid had apparently been overworked; the timer must have failed on DRAIN. The solenoid was severely overheated, and thankfully didn't cause a fire, but it was somewhat melted. Replaced the solenoid, and all is well, especially when my wife was eyeballing a $1000 Bosch!

Found great information on this site describing the problem. My 9 year old GE Triton dishwasher has not been draining. I thought at first it was something stuck in float somewhere or perhaps a bad pump, but after searching around, I found this site and other stories similar to mine. Most of the reports suggested a worn check valve in the floor of the dishwasher tub, apparently a common issue with some GE models. I removed the strainer located at the back of the tub (4 screws removed w/ 1/4" nutdriver), then unscrewed the check valve to inspect it. Saw that the valve seat was very worn. Ordered the replacement part, received it 4 days later and installed in less than 10 minutes. The best part was I didn't have to remove the dishwasher or crawl underneath to complete the repair. Well worth the $20 for parts & shipping.

1. Remove access panel under door. 2.Shut off hot water.3. Shut off electric to washer.4. Disconnect water line from water inlet valve.5. Remove small outlet water line from valve. Replace valve & reconnect. OR !!! 1.Take solenoid valve & bracket off of original inlet valve 2. Pull out white plastic diaphragm cover. 3. Remove diaphragm & clean out water holes with a pin. 4. Reassemble valve. 5. Reinstall original water inlet valve & save $27.00

The lower right and left tub baffles just slip in, no tools required. For the front door gasket; a) removed the backside of the front door by removing the door screws. You need to manipulate the front door latch to remove the panel. b) remove the existing gasket, replace with new gasket. The short 4" gasket was missing, which is why it was leaking in the first place. Replaced it with the new one. Reassembled and tested. Thanks to Parts-Select for a great experience, very well done site.

The shaft pulled out of the housing when I tried to get the push nut off. I had to take the pump housing out in order to get the shaft lined up with the valve when reassembling. In the end, the shaft had so much slop that no seal could keep it from leaking. Time for a new dishwasher.

I removed the four screws of the filter frame exposing the check valve (piston and nut assembly) . I unscrewed the old check valve and replaced it with the new one.

I received my dishwasher as a hand me down, my Aunt never liked the way it cleaned. After it sitting for about 2 years i installed it in my house and found that it leaked all the time from where motor shaft went into the pump housing. After disassembling everything and scouring parts sites online, I found the parts, ordered them. 3 days later i had the parts, and the next day I had a fully functioning leak free dishwasher.