40441 LG Washer - Instructions

PartSelect's instruction video on replacing this drain pump makes this repair doable even for a first timer like me. In addition to following the video instructions, I found that using plastic bicycle tire levers to reinstall the band clamp around the bellows was easier than using a screwdriver and less likely to scratch or damage the area. Beginners might want to take photos when disassembling the washer for reference if needed during reassembly. My washer's innards weren't exactly like the one in the instruction video, and the photos gave me a way to double check as I put it back together.

Disconnected power supply and water supply hoses. Laid machine on its back because this is a top load machine. Removed one bolt to take off stator then 6 bolts to remove rotor. Put it on side without taking off wire assembly. Snapped off rotor position sensor and installed new one. Put all back together and connected power supply and new stainless braided hoses. WORKS PERFECT. Thanks !

Disconnect elec., hot and cold water supply and drain hose. Lay washer on it's back. Removed nut from center housing. Removed screws from stater. Disconnected wires with flat screw driver at sensor and stater. Installes new sensor. Put everything back together. Washer works great. No LE code.

Unplug the washer! Turn off the HOT water valve. Remove the hot water hose at the connection on the back of the washer. Remove the two Phillips head screws holding the top of the washer. Slide the lid toward the rear until you feel it disengage, then lift it off, setting it aside.
Unplug the electrical connector on top of the hot water valve (just pulls off).using pliers compress the hose clamp, slide it away from the hot water valve and pull the hose off the valve fitting(it will have some water remaining so lift it up and secure it to the brace above the hoses).
Remove the two phillips head screws that hold the valve in place. Pull the valve toward the front of the washer to remove it and compare it to the new valve.
To install the new valve, reverse all steps insuring tight water hose clamp and electrical connection. Install hot water hose, plug it in and turn on water. Test run and check for leaks. Unplug it and reinstall top.

Wife called me and said the washing machine just flooded the Landry room. I looked at it and didn't see anything wrong. Took the top off and the back off and started looking for a leak, did not see anything. Took the front part of the washer apart thinking the drain hole was plugged up where the rubber boot is. It was ok after taking the big rubber boot off or whatever that is called i was not getting anywhere. I put it back together left the top and the back off. I turned the water on and started the washer on a quick cycle looking for a leak. I found the bellows at the inlet had a small leak fixed that and started the washer again. So what i found out was the clean out drain plug was not in tight letting water out as it was washing after i tightened it all was ok. So i did find a leak that was small that we never saw. The hardest part was putting that wire clamp on the rubber boot it took two people to do that.

We followed the installation video step by step that was found on another website.

E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.

Watched instructional video. Made it easy

bought a position sensor
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour

Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!

I looked this problem up on YouTube like I do with everything, I saw a video from this site.. so I ordered what I needed from the website. The parts came in I unpluged the washer from the wall very important, I literally removed 6 Philips head screws and unclipped the wires from the parts and removed the hoses with the pliers, hoses have squeeze clamps. Put in New parts put hoses back on wiring back on and I was done.. it took me a total of maybe 10 minutes.. NO MORE WATER standing in the washer.. Thank you!! I would recommend you add a video for the Inlet Valve Assembly like you have for the hot inlet valve though...

I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.

Had to manually shut off water valve behind the washing machine to stop the filling process. Followed repair video from the website.

I unplugged the washer shut off the water and disconnected the hoses. Then removed the top lid and removed old valves and installed new ones. Very easy plug and play installation.

Not too bad, had a neighbor help with the project as washer/dryer were stacked. removed dryer from on top out of way. Drained washer, tilted on side to get access from down below. Second person help here. unscrewed drain pump from front, Used pliers to unclamp hoses, disconnect wires to motor (already pulled power from wall) pushed plastic clip holding in unit and pulled out. New unit was factory new, not a knockoff. We took extra time to clean out hoses, especially from the main washer unit, it was a simple unscrew clamp and pull hose down. We sprayed out gunk from hoses and parts going back in. Once new unit was ready, installed back and reconnected hose and power. The clamps were somewhat of a pain with the overall size and angles to get them seated and on correctly. Much easier to take off, but take the time to reinstall correctly. Don’t need water leaking. Motor much quieter now, wife is happy.