403110 General Electric Dishwasher - Instructions

Removed the dishwasher from the cabinet. Turned it on it's top side. Removed the exit hose from the pump with a nut driver and replaced the flapper. Reconnected the hose to the pump.

Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order

Once I pulled the dishwasher out, I found that the tube drain assembly line was crimped. How this happened is beyond me. The dishwaser worked fine when we installed up till now. I believe the installer bent the tube when installing and eventually bent to a point where water would not drain out. Once the tube drain assembly was removed with a screwdriver, the new tube drain assembly was attached to the pump and the drain tube to the disposer. Very simple fix. The dishwasher is working like new. Thank you for your prompt service!!!

Kevin

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.

Pulled out the old one put the new one in . Simple and easy

remove lower rack. place in trash. place replacement rack into dishwasher

Repair is super easy and anyone can do it in no time!
At first my fear was that it was the pump, but after reading through the trouble shooting here it narrowed it down to the water inlet valve. The new valve even came with easy to read and understand instructions. I had it fixed in less time than it took my wife to make us lunch lol.

2 screws hold the mount bracket in place. Just remove the screws, remove the c-clip that holds the secondary/small water line on, pop the hose off then remove the main water inlet line [ its the bigger line with the brass fitting ] I only needed a pair of pliers for this. Reinstall the main water line into the new valve, but make sure you use pipe tape on the fitting or you'll have a water leak. Reinstall the secondary water line and reclip the c-clip using pliers to squeeze the clip. Hold the valve in place and reinstall the 2 mounting screws. That's it your done !!

This is the second time I've used partselect, and they are hands down the best !! Other sites would have you buying part after part until you happened to get lucky and get the right one. Not here, they help you figure out just what you need and nothing more.
Great people and fast service !!
Thank you once again.

get fingers between lower spray arm and drive flange - rotate arm counter-clock wise and lift off...the arm was warped and hitting inside of lower door liner.

The repairman offered to fix the dishwasher at a cost of about $200 or supply the water inlet valve for $85. Google led me to PartSelect.com where I easily found the correct part for $45. I received the part in 2 days by FedEx ground.
The hardest part of the repair was removing the dishwasher from the cabinet. I took the dishwasher out a short distance to the patio where I replaced the water valve...about 10 minutes.
I then made a makeshift connection to an outdoor water hose and connected the electricity and ran the dishwasher while out on the patio through a short cycle to make sure of the repair and check for leaks.
Then reinstalled into the cabinet...total time about 2 hours.
Thank you PartSelect.com

Open dishwasher and remove the bottom spray wheel, filter, and unscrew the mounting bracket to release the pump connector below the bottom of the unit. Remove mounting screws at top front of dishwasher and carefully slide the unit out; you may have to pry side panels inward with a flat screwdriver in order to get the dishwasher past any cabinetry. Be careful not to pull the dishwasher too far out as the water supply and drain hoses could be damaged. Unplug the unit. Turn unit sideways and tip over onto its' back. At this point, the sump will have to be removed using a nut-driver and/or socket set. This will open access to remove the old pump connector. Replace the old connector with the new connector, and reassemble the sump, connecting and firmly tightening all connectors. Tip unit upright. Screw mounting bracket back into the bottom of the dishwasher and put the remaining parts back. Before pushing the unit back into it's nook, I advise running a quick cycle just to make sure there is no leakage. If there is no leakage, put the unit back, tighten the mounting screws and you're done.

Disconnected the electricity, the drain hose, and the water supply from the dishwasher. Loosened the two screws from the countertop and pulled out the dishwasher. Turned it on to it's side. Saw the damaged inlet sump. Had to remove the Pump connector to get to the inlet sump. Checked it also and discovered that it was starting to develop a small crack from the inside. I decided to replace it as well. The job involves removing the hose clamps and removing the spray mechanizm from the interior of the dishwasher to spin out the inlet sump. Not a difficult job.

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.

Removed the lower rack and installed new wheels with clips

Took the rack out. Took off the broken wheels and axles. Popped the new ones on, while replacing the rack. Piece of cake! Saved over $100.