3LMVWC100YW1 Maytag Washer - Instructions

First removed the cap, took out the screw, pulled out old agitator and replaced it with the new one

I popped of the fabric softner dispenser at the top auger by appling pressure with both thumbs rather than use the notch provided. This gives access to the agitator mounting bolt which was removed with a deep socket and extension on a ratchet handle. The agitator slipped right off the splined shaft by pulling upward at two points at the b ... Read more ottom. I ordered the complete agitator repair kit which included a part that improved the operation of the top auger, it may have been a factory upgrade at some point on this machine. I did use silicone grease where required and I feel that this is a must for longevity of the thrust washer. If you are ordering the complete kit, the o-ring seal for the inner cap is included. The machine washes like it was new.

1. Removed the fabric softener dispenser

2. Removed Barrier Seal Cover

3. Removed bolt and seal

4. Removed and replaced CAM Agitator Assembly

5. Reversed the removal steps.

I removed the cap over the ratchet mechanism, removed the ut holding the agitator in place, removed the agitator and cleaned all the parts. The assembly for the ratchet dogs was a 3 piece assembly that was included in the kit I bought from Part Select. I also bought a new cap and gasket since my old gasket had broken too. A new gasket ... Read more was already included in the kit, so I didn't need ot buy the cap. I liked that th ekit included everything I needed and good instructions. parts got to me in about 3 days. Very happy with my Parts Select experience and the fact I saved at least $100.

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the a ... Read more gitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

the repair went well but I still haven't received a refund for the order was was sent incorrectly. Order #22085769 order date 2/3/23

Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!

I just ordered the complete agitator kit since I didn't know for sure what I all needed, and it made my repair so easy replacing since it was all complete. I followed video which was a great help. Got it all done in 25 minutes. Very easy. Thank you...

Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.

Had to clean out area where bolt was to go as it was full of debris. Placed agitator on, bolted on , placed softener dispenser on. Done

Super easy. Watch the video on YouTube.

take off top on middle section (pops off) pop dispenser on--done

snapped off the softener dispenser, pulled out the plastic seal below and could see problem. Used socket with extension to remove agitator. ran machine to verify transmission was working.
Looked up parts on line and found Part Select. The repair stories insured me I had correctly identified problem. Ordered part on Sat. arrived Tues. ... Read more Reversed disassembly process with new agitator. Success
Great source of information, fast delivery, very satisfied overall and will reccomend and use again

Removed the attaching bolt and then removed the Upper Agitator Assembly. I removed the damaged parts and installed the Agitator Repair Kit and Re-installed the NEW Upper Agitator Assembly.

All of our wash was smelling like mildew. It was making us nauseas . After the repair everything smelled fresh and clean again. We recei ... Read more ved our parts within three days.

Thanks