38481KBRCRWW General Electric Refrigerator - Instructions

My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!

I came home to find a mess near the refridgetor. My teenage daughter or son had made themselves a peterbutter and strawberry homemade jam sandwhich. The strawberry jam was all over the inside of the door and on the floor. What a mess, so I was waiting for my husband to change the gasket around the door anyways. So I though to myself I just change it myself. The old one just came off and I pulled the new one out of the box and I went right on with not much effort. ( I wiped down the area after I put off the old gasket) Thank you very much for making the parts so easily avaiable on your website without having to buy a new refrigator. Thanks again Sue and Ed

2 screws. how easy can i get.

Because the kit did not include fasteners, had to use wood screws and superglue.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Connected the 2 wires and pushed in the switch until it clicked.

The repair is very simple, the gasket sits in a channel in the door. Just start with a corner and pull the old gasket out. Once you've removed the old gasket, push the new gasket into the same channel. Make sure you've completely pushed in the new gasket all the way around the door. It's as simple as that. The repair takes less than 5 minutes per door.

Defrosted the refrigerator,power off and cut the 2 wires on thermostat and sodered the new one on and shrink tube sealed the wires,refrigerator works like new!

I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

layed fridge face first on a chair removed cover with flat head screwdriver unplugged part replaced with new part replaced cover returned to upright and plugged in

Only took a screwdriver to take two screws out & install new slide with the two existing screws. Very easy. Took less than 5 minutes. Great website I found on Google right away, just by searching for refridgerator parts. After ordering part, only took a few days to come in.