My Orders
- Home
- 3639524710
- Instructions
3639524710 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken auger in the bucket assembly.
6 of 9 people
found this instruction helpful.
-
Chip from Mandeville, LA
- Easy
- Less than 15 mins
-
Nutdriver
I ordered the wrong part, the ice maker assembly, because your diagram was not marked properly. I returned the part and you credited my account. Thanks. Ordered the new bucket. It worked fine. Now I have ice and crushed Ice whenever I want. Thanks.
p.s. I didnt use any tools, but to satisfy you I select nut driver.
p.s. I didnt use any tools, but to satisfy you I select nut driver.
Was this helpful?
Thank you for voting!
Ice Maker would not fill.
5 of 6 people
found this instruction helpful.
-
Charles from Keller, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.
Went ahead and installed the unit, using the supplied electric cable adapter.
A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.
Went ahead and installed the unit, using the supplied electric cable adapter.
A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.
Was this helpful?
Thank you for voting!
crushed ice feature inoperative, broken pieces in water dispensed.
6 of 9 people
found this instruction helpful.
-
Jim from Jacksonville, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exa
... Read more
ctly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!
Read less
Was this helpful?
Thank you for voting!
Fresh Food section door made a click noise on closing
5 of 6 people
found this instruction helpful.
-
Charles from Renton, WA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Since the cam riser was obviously broken I obtained a replacement.
It also broke. The door hinge cam needed to be replaced also.
To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam. ... Read more r />Replace in reverse order.
Be sure to inspect all parts and order all required.
It also broke. The door hinge cam needed to be replaced also.
To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam. ... Read more r />Replace in reverse order.
Be sure to inspect all parts and order all required.
Read less
Was this helpful?
Thank you for voting!
The Icemaker failed to make ice
8 of 16 people
found this instruction helpful.
-
Dean from Folsom, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I pulled the refrigerator away from the wall and turned off the water to the refrigerator and unplugged it from the wall. After removing the icebucket from the freezer I located the mounting screws, loosened them, unplugged the electrical connection below the icemaker and carefully removed it from the freezer. I unpacked the replacement i
... Read more
cemaker, matched it against the original and attached the electrical connection adapter. Using the slots provided on the new icemaker I placed it over the mounting screws after aligning the water inlet pipe properly. I tightened the mounting screws while maintaining the icemaker in a level position. I plugged in the electrical connector. Then I replaced the icebucket, plugged in the refigerator back into the 110VAC outlet, turned on the water and repositioned the refrigerator in it's normal position.
Read less
Was this helpful?
Thank you for voting!
no ice made
5 of 8 people
found this instruction helpful.
-
Robert from San Marcos, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Performed self test.turned off ice maker switch four 5 minutes.Then turn on switch,within 10 seconds,pushed ice paddle 3 times,with 1 second in between each push.Push all the way back and release. Ice maker should cycle and squirt water. My ice maker did neither.I unplugged cord from fridge.So i replaced the ice maker.After a couple of s
... Read more
crews had ice again !
Read less
Was this helpful?
Thank you for voting!
Auger was rusted causing brown spots in ice and metal pieces in water
4 of 5 people
found this instruction helpful.
-
Jane from Clifton, NJ
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Took unit apart but did not take photos of how to put unit back together, so needless to say it took longer then it should have. My error. Ordering the part was very easy and within days the part arrived at my door. Should the need arise, I would order again from Part Select.com.
Was this helpful?
Thank you for voting!
would not crush ice
3 of 3 people
found this instruction helpful.
-
Larry from Mount Airy, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.
Was this helpful?
Thank you for voting!
Ice maker needed replacement
3 of 3 people
found this instruction helpful.
-
James from PLYMOUTH, MA
- Really Easy
- 15 - 30 mins
-
Socket set
Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.
Was this helpful?
Thank you for voting!
My ice breaker started leaking and making noise anf the stripper broke.
4 of 6 people
found this instruction helpful.
-
Marie from Elk Grove Village, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver
I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.
Was this helpful?
Thank you for voting!
Ice maker filled too full and ice froze in the basket and a piece was broke on the icemaker itself.f
3 of 3 people
found this instruction helpful.
-
Karen from SAN ANTONIO, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
My son did it , and showed me what he did when he was finished.
Was this helpful?
Thank you for voting!
Door was squeaky and would no close
3 of 3 people
found this instruction helpful.
-
Ronald from Yuma, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and ap
... Read more
plied a little lubricant to the cam and job complete.
Read less
Was this helpful?
Thank you for voting!
Made ice would not eject from ice holder bin
3 of 3 people
found this instruction helpful.
-
Lynn from MOUNTAIN HOME, ID
- Very Easy
- Less than 15 mins
removed broken bin , slid new ice bin in closed door. I bought the complete part.
Was this helpful?
Thank you for voting!
None
3 of 4 people
found this instruction helpful.
-
Lee from San Antonio, TX
- Really Easy
- Less than 15 mins
Simple snap in place.
Was this helpful?
Thank you for voting!
icemaker stripper fall a part
3 of 4 people
found this instruction helpful.
-
Ted from Harrisonburg, VA
- Easy
- 15 - 30 mins
-
Screw drivers
instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.
Dremel and it works!The instalation part of the "job" was less then 10 min.
Was this helpful?
Thank you for voting!