Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Rust on Metal auger leaving rust in ice...
5 of 5 peoplefound this instruction helpful.
Mike from St. John, MO
A Bit Difficult
Less than 15 mins
Nutdriver, Pliers, Screw drivers
Disassembled front door/cover (3 screws), then removed deflection door assy, (4 1/4" nuts), CArefully and methodically removed C Clip and grinder teeth...Be careful with this step to document/remeber how to re-assemble! Auger repleced then reverse steps... All in all, not too bad, but you can easily screw up the teeth re-assembly.
Was this helpful?
Thank you for voting!
Unit had stopped making ice
5 of 5 peoplefound this instruction helpful.
Ron from ORANGE, CA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.
Was this helpful?
Thank you for voting!
crushed ice feature inoperative, broken pieces in water dispensed.
6 of 9 peoplefound this instruction helpful.
Jim from Jacksonville, FL
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exa
... Read morectly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!
Read less
Was this helpful?
Thank you for voting!
broken auger in the bucket assembly.
6 of 9 peoplefound this instruction helpful.
Chip from Mandeville, LA
Easy
Less than 15 mins
Nutdriver
I ordered the wrong part, the ice maker assembly, because your diagram was not marked properly. I returned the part and you credited my account. Thanks. Ordered the new bucket. It worked fine. Now I have ice and crushed Ice whenever I want. Thanks.
p.s. I didnt use any tools, but to satisfy you I select nut driver.
Was this helpful?
Thank you for voting!
Fresh Food section door made a click noise on closing
5 of 6 peoplefound this instruction helpful.
Charles from Renton, WA
Easy
15 - 30 mins
Screw drivers, Socket set
Since the cam riser was obviously broken I obtained a replacement. It also broke. The door hinge cam needed to be replaced also. To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam.
... Read morer />Replace in reverse order. Be sure to inspect all parts and order all required.
Read less
Was this helpful?
Thank you for voting!
Ice Maker would not fill.
5 of 6 peoplefound this instruction helpful.
Charles from Keller, TX
Easy
15 - 30 mins
Screw drivers
Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.
Went ahead and installed the unit, using the supplied electric cable adapter.
A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.
Was this helpful?
Thank you for voting!
The Icemaker failed to make ice
8 of 16 peoplefound this instruction helpful.
Dean from Folsom, CA
Really Easy
15 - 30 mins
Screw drivers
I pulled the refrigerator away from the wall and turned off the water to the refrigerator and unplugged it from the wall. After removing the icebucket from the freezer I located the mounting screws, loosened them, unplugged the electrical connection below the icemaker and carefully removed it from the freezer. I unpacked the replacement i
... Read morecemaker, matched it against the original and attached the electrical connection adapter. Using the slots provided on the new icemaker I placed it over the mounting screws after aligning the water inlet pipe properly. I tightened the mounting screws while maintaining the icemaker in a level position. I plugged in the electrical connector. Then I replaced the icebucket, plugged in the refigerator back into the 110VAC outlet, turned on the water and repositioned the refrigerator in it's normal position.
Read less
Was this helpful?
Thank you for voting!
no ice made
5 of 8 peoplefound this instruction helpful.
Robert from San Marcos, CA
Really Easy
15 - 30 mins
Screw drivers
Performed self test.turned off ice maker switch four 5 minutes.Then turn on switch,within 10 seconds,pushed ice paddle 3 times,with 1 second in between each push.Push all the way back and release. Ice maker should cycle and squirt water. My ice maker did neither.I unplugged cord from fridge.So i replaced the ice maker.After a couple of s
... Read morecrews had ice again !
Read less
Was this helpful?
Thank you for voting!
All the shelving rails had cracked, vegetable and meat storage bins dropped.
4 of 5 peoplefound this instruction helpful.
Wayne from Warner Robins, GA
Really Easy
15 - 30 mins
Screw drivers
Removed the storage bins, unscrewed the old rails, screwed in the new rails and saved a Sears service call plus their mark up on the parts. Estimated savings was about $100.
Auger was rusted causing brown spots in ice and metal pieces in water
4 of 5 peoplefound this instruction helpful.
Jane from Clifton, NJ
A Bit Difficult
More than 2 hours
Nutdriver, Pliers, Screw drivers
Took unit apart but did not take photos of how to put unit back together, so needless to say it took longer then it should have. My error. Ordering the part was very easy and within days the part arrived at my door. Should the need arise, I would order again from Part Select.com.
Was this helpful?
Thank you for voting!
Ice maker filled too full and ice froze in the basket and a piece was broke on the icemaker itself.f
3 of 3 peoplefound this instruction helpful.
Karen from SAN ANTONIO, TX
Really Easy
15 - 30 mins
Screw drivers
My son did it , and showed me what he did when he was finished.
Was this helpful?
Thank you for voting!
My ice breaker started leaking and making noise anf the stripper broke.
4 of 6 peoplefound this instruction helpful.
Marie from Elk Grove Village, IL
Really Easy
15 - 30 mins
Nutdriver
I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.
Was this helpful?
Thank you for voting!
would not crush ice
3 of 3 peoplefound this instruction helpful.
Larry from Mount Airy, NC
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers
you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.
Was this helpful?
Thank you for voting!
Door was squeaky and would no close
3 of 3 peoplefound this instruction helpful.
Ronald from Yuma, AZ
Really Easy
Less than 15 mins
Nutdriver
I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and ap
... Read moreplied a little lubricant to the cam and job complete.
Read less
Was this helpful?
Thank you for voting!
Needed left and right drawer rails for crisper
4 of 6 peoplefound this instruction helpful.
Joanne from West Columbia, SC
Really Easy
Less than 15 mins
Screw drivers
I was so pleased to find your website. We have just one company here in Columbia,S.C. that sells refrigerator parts. I did find out that they wanted about $60.00 for both pieces. Needless to say,I was just going to do without. I knew there had to be someone else. I found you guys on line,ordered my parts for a little over $5.00 a piece,an
... Read mored I put them in myself. I'm talking standard GE parts,not knockoffs. I am so pleased. Thanks for being there. I tell everyone about you.
My Orders
