3638502583 Kenmore Refrigerator - Instructions

I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and ap ... Read more plied a little lubricant to the cam and job complete.

removed broken bin , slid new ice bin in closed door. I bought the complete part.

Removed 2 screws that hold it on, put the new one in with the 2 screws that were removed.

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable s ... Read more hould be more flexible and adapt to the fridge a little more friendly.

instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker ... Read more and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.

Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"

replaced lights in refrigirator and freezer

First removed the old sliders, then screwed in the new sliders, replaced all four within minutes.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic ... Read more door jamb putting the new unit in but other than that all is well and functioning well.

Got the part in and needed two screws to installed on left side. Service was great on the part as it was delivered in 3 days from the time we ordered. Thanks for the quick service

Each rail required removing two screws which were used to install the new rail. Each one took about 5 minutes however cleaning the recesses was the most effort.

Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door ... Read more now self closes .

First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.