36371542410 Kenmore Washer Dryer Combo - Instructions

Took unit practically apart to remove old parts and install new part. Unit is like new.

This is the 2nd time we had to replace the slides. Not a big deal. Removed the top & front of the dyer and replaced the new slides. It's also a good time to vacuum out the inside while you have it apart. Be advised.... Get your tools ready. You'll be receiving your parts quickly. Couldn't believe how fast they arrived!

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.

Removed gas line. removed control panel, removed top, removed front, removed burner, replaced igniter, put back in. paused and played the video. very easy to do. 42 minutes and I had a few beers.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

Studied the symptoms online. Disassembled the unit and found the drum slides worn out. Ordered them and a new belt. Installation videos on Parts select web site were helpful. The dryer runs quiet now. I need a front bearing unit, but the slides are working ok for right now.

To get to where the drum slides go you have to first remove the dryer top. Then you have to remove the two screws that hold the dryer front/door. Found inside the dryer about an inch down on both sides. Be careful because it will fall off. Lower carefully as there is an electric hook-up on the bottom of the door. On the door top are the brackets that the slides slip into. My dryer has 4 slides. Sold individually for some reason. You are done except for re-assembly. Slip dryer drum back on door, press the front until you hear it click back together. Put screws back in and top back on. You are done and no more screeching!

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

replaced the parts that had worn out

Good thing my husband is so handy. This part was very difficult to get to. Basically, he had to take apart almost the whole dryer. There is no access door so the side panel had to be removed, but before you could do that the front panel and door had to come off, then the top of the dryer. Keep track of the screws, we had a few leftover! But the dryer works great again and we hope to get several more years out of it. We've had no problems with it until now and it's over 15 yrs. old.

watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.

I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes