All Installation Instructions for Kenmore Refrigerator 36368667894

Light socket missing in refrigerator

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

Parts Used:

Light Socket

Wayne from Issaquah, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

sweating

i found that the door was to low was the problem shimmed the hinge on the bottom brought the door up so the gasket was ok so isent the new gasket back to you never attempted to change so i dont have any thing to tell you about instalation difficulty carl phillips

Parts Used:

Fresh Food Door Gasket

carl from zephyrhills, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light in freezer section not working

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Parts Used:

Light Switch

Victor from Fort Myers, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

6 of 24 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Fridge not cooling

Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good

Parts Used:

Condenser Fan Motor - 115V

Pedro from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Bar end cap broke

Just snapped in.

Parts Used:

Door Shelf Retainer Bar End Cap - Left or Right Side

Gery from Tavares, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

light switch quit working

removed the inside fridge electrical panel and swapped switches

Parts Used:

Light Switch

David from Simpsonville, SC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

sticky switch

easy pry out, disconnect wiring, connect on new switch and press in switch.

Parts Used:

Light Switch

ANTHONY from NEW EGYPT, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Replacement gasket

I took it right out of the framed box to keep the gasket in shape and snapped it back on the gasket mount on the freezer door it took 5 minutes or less perfect fit

Parts Used:

Freezer Door Gasket

Dewey from Laurel, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Foam Air Duct damaged by defrosted meat

Removed ice cube tray and fan cover using a cross-tip screwdriver. Old air duct foam had been damaged by defrosting meat and made entire refrigerator smell. Part easily slides out and slid in knew foam. Replaced with new air duct foam after thoroughly cleaning refrigerator by sliding it into place, replacing fan cover and ice cube tray. Hardest part of entire replacement was cleaning refrigerator. The actual replacement of the part took less than 15 minutes.

Parts Used:

Air Duct Foam

Benjamin from Virginia Beach, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

light would not stay on

First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.

Parts Used:

Light Socket

Kenneth from Leavenworth, KS
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

needed new light socket

Pulled out old socket.pushed in new one.

Parts Used:

Light Socket

Charles from Williamsburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

broken crisper drawer support

quick and simple--removed the old one and slid new part in on same support pins.I had the new part via UPS LESS THAN 24 HRS.FROM THE TIME I PLACED THE ORDER! THANKS, SOMEONE IS REALLY ON THE BALL.

Parts Used:

Vegetable Pan Cover - Glass included

Richard from Owls Head, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

failed light switch

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Parts Used:

Light Switch

Jules from Crowley, LA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

lost screw and insert plug

replaced the screw and covered it with the plug. The pleasant surprise was that the requisite screw plug were available, especially after over 10 years.

Parts Used: