36361542 Kenmore Washer Dryer Combo - Instructions

The parts came very quickly, and they were the exacxt parts which made installation very easy.
Just open the dryer door, there are 2 screws to remove right above the dryer door that holds the top plate of the dryer. slide the top of the dryer top off by pulling up and ouyt towards you. There are 2 screws that hold the front of the dryer, remove the 2 screws and the front of the dryer will come out towards you. The drum will fall a litttle towards you.
I let the dryer front lean on my leg and snapped out the bearing and drum slides replaced it with the new one. Reverse the order of taking it apart
Now my dryer sounds as quiet as the first day I bought it.

We had a squeeking sound coming from our dryer which I felt was probably the belt. When I removed the front of the unit and saw the condition of the slodes and drum bearin, I ordered a set from PartsSelect.com. It only took about 20 minutes to repale the parts, and 5 of that was figuring out the bearing just "snaps on" (I was afraid to just yank it for fear of breaking something else). Probably saved like $75 or so between the parts markup and a service call by doing it myself.

loosened two hose clamps and four screws to replace the anti siphon valve.

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

Poped the top off took out two screws, pulled the front off removed the old parts and put in the new ones.

Removed two screws to remove top to access drum. Removed two screws to remove front panel. Easily removed drum bearing and snapped in new bearing. 4 Glides were slid into slots. Only one problem. My service parts list called for drum bearing #WE3X37. I was sent #WE3M26. I was assured this was the right part for my dryer. Although the part did fit, I was unable to use the existing light because the the hole on new bearing was too small to accommodate it. Replacement of drum bearing would not be necessary if GE would put visible labels on dryer warning consumers of preventive maintenance of glides that wear.

Took off control panel,top,leftside facing door,and,door panel. Replace the 2 green and 2 white slides, the front drum bearing, the rear bearing and groundind strap behind the heating element,and new belt. Put back together,run's and sounds like new. The hardest part was putting drum bearing in inside and backside of drum by yourself. Replace belt with left side panel off. Easy to get on that way.

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

Your instructions were execellent
Problem is solve
Thank you

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

Our dryer was making an ear piercing high pitched squeal. I didn't know what it was, but through a quick search on this site determined that the Drum Bearin and Drum slides must be out. I ordered the items and they quickly arrived. I followed the skeematic of the dryer that they had on the site and it ended up being one of the easiest "do-it yourself" fix jobs I have been involved with in a long time. I will definitely come back to this site when I have future appliance issues.
By the way, I am an accountant by trade and have no previous appliance fixing skills.

1. remove top
2. remove front panel
3. remove/replace drum bearing
4. replace panels
5. enjoy cold beer

save yourself money working on your own appliances. appliance repairs often times don't require special tools, are very easy to diagnose and repair.

The repair was very easy. Had to remove the front of dryer, parts fit great. It was worth the extra money to ship parts next day then to listen to the squeeking anymore.

Thanks to this site I was able to get the parts fast!!!

I noticed that some clothes were coming out of the dryer looking like they had been chewed on. The next day something actually caught on something inside the dryer near the door. There was a broken piece of plastic. I wrote the dryer model number down and came to this website. I easily determined it was the drum bearing from the pictures provided by this website. The part came 5 days later. I think it would have been sooner, but I ordered on a Friday before a 3 day weekend (Memorial Weekend). I did not order the slides recommended to be ordered with it because my dryer was not making noise. When I replaced the drum bearing, one slide was worn completely through and the others were fine. The one worn through was right near where the plastic on the drum bearing was broken. I ordered a green slide to replace the one that was worn through.

Replacing drum bearing required the removal of 4 screws total. 2 inside dryer doorway, these two were facing towards the ceiling. After removing those two the dryer top popped off easily and did not require the removal of the control panel at the back of the dryer. The other two screws were inside and were small screws which held the front dryer panel onto the sides. After these were removed I pulled the front panel away enough to get to the drum bearing. Easy Peasy!

This repair was so easy..removed four screws and replaced front bearing(big plastic peice) and four small plastic peices...project done in less than 15 minutes!!!