36359492990 Kenmore Refrigerator - Instructions

Pretty much self explanatory.Removed drawer and anything on top of glass shelf.Remove two screws holding on slide.Replace with new slide.Repeat on other side.Replace shelf and drawer.

After trying to reconnect a flexible hose to the water valve several times I stripped the connection to the water valve, causing it to have a slow leak.

Twice I tried to have an appliance parts store order the part without success. (I even brought them the part from the refrigerator to show them how it looked. ) they ordere ... Read more d the wrong part two times and then said they could not figure out what part I needed.
Finally my wife and I went on line, keyed in the model number and searched for parts of the refrigerator related to the ice maker. We saw the correct part and ordered it ourselves.

It was a success. I changed the part within 30 minutes and the ice maker has been working ever since. I would search and find a part on my own again before trusting someone who supposedly sold parts as their business.

I had looked at videos on you tube,it looked simple enough. I mostly do my own repairs so I gave it a shot. the job went well,if you do not fix things around the house don't try to do the repair,find a handyman in your neighborhood to help you out,cheaper than calling a refrigeration man. It is not that hard to do.

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exa ... Read more ctly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!

First Remove the screw and cover from the left top front of the fridge using a Phillips Screw Driver # 2
Then using a nut driver 1/4 of inch (or Socket set)
remove the two nuts holding the door hinge keeping the door in closed position. Now unplug the electrical connector between the door and the fridge body(Simply pulling it ap ... Read more art) Now hold the door from the middle and raise it up so that it can slide out from the bottom hole, on the main body
Now place the door on a table or a flat surface(Put may be a sheet or some thing to prevent the finish from getting scratched) Now remove the nuts around the inner panel of the door(nut Driver or Socket set) Remove the old lining and discard .Install the new lines and then replace every thing in the reverse order.
Note : Before tighting the top nuts of the door, make sure you keep the door aligened so you would not have to do it after completeing the job.

Procedure for Replacing the Ice Chute Plate
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) ... Read more that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.

Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.

Went ahead and installed the unit, using the supplied electric cable adapter.

A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.

I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it ... Read more couldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!

repair was simple removed glass shelf and removed the two screws holding rail in place. I was really amazed at the quick service that I had receiced, I ordered two of the same part and they had the instructions to send back the additional part in my email the next day. Thanks for your help.

Easy repair. Snapped cover off control panel. Removed 4 phillips head screws on control board assembly. Removed (2) connectors from assembly and pulled out defective unit. Installed new control board in reverse order. Everything now working. Very fast and easy repair once you have the part.

remove screws from broken rails and install new rails with screws.

Very simple fix. Unscrewed broken drawer rails and replaced with the new. No big deal. But again, these seem very flimsy for this model of refrigerator. they should use metal drawer rails with rollers to better accomodate the wieght of produce in the drawers.

All i had to do was pop off the front trim, remove 4 small screws, unplug two plugs and replace the board.

It took me a grand total of 9 minutes to get the job done.

Way cheaper than having a repair man come to the house twice, once to diagnose, and once to replace the board he would have ordered and marked up.

I ordered the wrong part, the ice maker assembly, because your diagram was not marked properly. I returned the part and you credited my account. Thanks. Ordered the new bucket. It worked fine. Now I have ice and crushed Ice whenever I want. Thanks.

p.s. I didnt use any tools, but to satisfy you I select nut driver.