36348047892 Kenmore Refrigerator - Instructions

Took the stuff out of the door
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door

You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.

My 7-year-old son helped me - it was a fun father-son project.

parts ordered fit perfectly made repair removed items from shelves removed door avd replaced hinges and reassembled 1/2 hour total by myself

After reading other posted comments,I ordered a new hinge assembly set ps290199. My helper and I removed the door and laid it on the kitchen table. While he replaced the hinge on the refigator,I replaced the cam on the door bottom. We re-hung the door and completed the job in 15 minutes with the door closing like it did when new.

I read the details and bought the pair, as directed from other bloggers. I got the hinge piece, followed others advice and had it all done in not time! Saved a lot of money and will use this website again!

Lifted the door while closed into position even with freezer door. Then put srap pieces of wood under door to hold into place while I removed the old hinge assembly and replaced with the new one. The door works good now. Make sure you replace both peices as they will both be worn.

Just remove all items in door shelves, remove screw holding top hinge cover on. Remove two bolts holding top hinge and remove hinge from door. Carefully open door and lift out of bottom hinge. Remove screw holding bottom hinge on door and replace broking cam riser. Reinstall door in reverse order and adjust top hinge where both doors are even across the top. Thats it!!!!!

Removed guards and covers, (2 snap connections, 3 phillips head screws) Removed two 5/16" screws, removed door, removed cam from bottom of door, installed new items.

Worked Great!!!

First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new lower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!

very easy, thanks for the great selection for parts.

First issue, I tried to get the top hinge cover off by gently prying. No go. Went to get a step stool and discovered a small screw holding the plastic cover on. At least I didn't break it by prying. I then removed the two top hinge bolts and removed top hinge. I then lifted the door off the bottom hinge.

I then removed the bottom hinge (two bolts) and replaced it with the new hinge with the attached lift cam. (Bottom half of cam)

I then removed the broken lift cam from the bottom of the door, replacing it with the door closing cam included in the hinge assembly package.

Second issue: I did not need to order the DOOR closing cam as a separte item as it came with the hinge assembly package. (There was a warning note in the hinge assembly package to use the door cam included, as new materials had been used and abnormal wear could occure if you didn't replace both pieces of the lift cam)

I set the door back on the bottom hinge, replaced the top hinge and tested. The door would NOT close on it's own. Getting down on my belly I could see resistance of the door light switch was keeping the door from closing. The fix of this issue was to load the door with the normal use items. This provided enough weight to the door and offset the resistance of the switch. EVERY THING WORKED GREAT. Time was 26 minutes from start to finish.

Part no. Ps290199 received matched part no. Ordered, which I obtained from your web site, however, part did not exactly match oem part. It was necessary to drill a new top hole in each of the hinges. New hole center was drilled 1/2" off (lower) then hole in supplied part. Jpb could have been accomplished easily by the avg. Homeowner, but the drilling required a little more skill & possible some tools that an average homeowner does not possess. Otherwise job was relatively easy and satisfactorily completed.

Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.

I had to remove the top hinge of the door and shut off the water supply to the automatic ice maker. I then unhooked the water line and pulled it through the guide as I took the door off. Once the door was off, I removed one bolt with the nut driver and replaced the cam. I reversed the above actions and replaced the door. It is very important to adjust the door so the seal fits tightly and evenly all round the door. It was a relatively simple procedure that went very smoothly.

1. Blocked up the door keep it steadily and enable ease access to screws.
2. Removed screws holding the door closing cam and lower door attach bracket.
3. Disconnected clamp holding the water supply line for the water and ice dispenser and disconnected the water line at the joint.
4. Removed the broken cam and put the new one in it's place, threading the water supply line through the hole of the cam.
5. Put everything back together in reverse sequence of removal.

Followed other messages to complete fix. Simple overall.

Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.