36348047892 Kenmore Refrigerator - Instructions

Removed everything from the refrigerator door. Removed the screw holding the cover over the top hinge. Removed the two (8mm) bolts holding the top hinge to the refrigator. Removed the door. Removed the plastic grill/cover and the two (8mm) bolts from the lower hinge assembly. Installed the new hinge assembly. Replaced the closing cam (included in the hinge assembly kit) on the bottom of the door. Put the door back on the lower hinge. Installed the upper hinge. Adjusted the door and tightened the bolts on the upper hinge, and replaced the hinge cover. Done!

Removed the door by removing the top hinge and lifting it off the broken bottom hinge/cam assembly. Removed the broken hinge/cam assembly found out why the cam broke the doorstop was bent so I had to order the doorstop also. The ordering of the parts was so easy. They shipped them on Monday and they arrived the next day. I will use Parts Select again

replaced lights in refrigirator and freezer

put block of wood under the door, removed old hinge and installed the new one. about 15 minutes

I took the glass plate off the top of the drawer, then removed the draw. I then removed the two screws holding the slide rail. I put the new slide rail in place, put the screws back in it, slide the drawer back in place and replaced the glass top. nothing to it.

installed 3 of 4 shipped parts. ended up with 2 upper right hand slide rails, even though ones package said upper left.

First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.

took 2 philips screws out,took off rail,and then nreverse.these steps,

Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes

First I removed glass shelf on top of rail. I then removed the two screws holding rail to refrigerator side. Next I installed new rail using same two screws. Finally I replaced glass shelf on top of rail.

Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.

Removed 2 screws replaced new part very easy

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Followed the video on the computer. Was fixed in no time. Works great.

I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair