36315465792 Kenmore Dishwasher - Instructions

easiest way i found to do it was pull dishwashers out from under the cabnet... laided a pillow down in front of the door and turned it on the front side... the part was very easy to get to at this angle....could have done it in less then 5 minutes but took my time to double check everything to be safe....took a total of about 10 minutes.. ... Read more ... very happy now no longer need to vacume out the old dish water left at the bottom of the dishwasher...... i think most anyone could do this very easy....

Put on a new cap.

The dishwasher was in a rental so I didn't want to spend the money for a new one. The part was expensive compared to a new (cheap) dishwasher. The order was shipped promptly and arrived when I expected even though it was Christmas time. The part fit perfectly and everything is back in place.

Once realized needed to open the wheel rail a little to remove wheel stop, it wasn't too difficult. Took about 20 minutes. Part came in a couple of days and was the correct part. Was disappointed that a similiar part, looked the same on the web site costing about $54.00 plus shipping, ended up costing about $100.00. Contacted customer se ... Read more rvice, said I needed to contact the factory. Seems like they should have researched the problem, Andy Duer

We ordered the pump kit by model number and it was a perfect match.(It was on our door step in 2 days with normal shipping!) Three bolts and a couple of electrical connections later and the pump was off The install was just as easy. The instructions were very easy to follow.It's great to find a company these days that knows what it is doi ... Read more ng and does exactly what it says it will do.
Kudos and thanks!

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our T ... Read more hanksgiving family get together.

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

i unscrewed old part and replaced with new one. Didn't know how to do it but figured it our quickly.

I removed the two screw at the top holding the dishwasher to the counter top; pulled on the unit - but found it stuck on something.
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected thes ... Read more e from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.

I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn

Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy

Took end caps off roller guides. Slid old out...slid new in...poped end caps back on...done. Too EASY!