36314779100 Kenmore Dishwasher - Instructions

All Instructions for the 36314779100
121 - 135 of 321

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Leaking small hose.
2 of 3 people found this instruction helpful.
  • Bruce from Isleton, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
At first I thought I would call a repair man.Then I thought-that will be at least $100!So we went online and found the part.Took about four days to arrive.I pulled the dishwasher out and turned it on it's front.The little leaking hose was easy to remove,two clamps,and the new one installed.Total cost-$14.00.
Was this helpful?
Thank you for voting!
dishwasher did'nt drain water . solinoid was melted and stuck
2 of 3 people found this instruction helpful.
  • Ben from florida, MI
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.
Was this helpful?
Thank you for voting!
water left in dishwasher after wash
2 of 3 people found this instruction helpful.
  • mike from tampa, FL
  • Easy
  • 15 - 30 mins
  • Socket set
Open door, remove lower wash rack, remove 4 screws holding screen in rear of inside tub with 1/4 inch socket. Unscrew piston and nut assy for checkvalve, sounds like a mouthful but it is only 1 part. Checkvalve has 2 small ears on it which allow you to twist it out, it has treads on it. Flapper on check valve flapper rots away and water pumps back into tub instead of being routed to drain line to garbage disposal. Part with shipping was just over $20.
Was this helpful?
Thank you for voting!
Dishwasher would not drain
2 of 3 people found this instruction helpful.
  • kevin from wellington, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.
Was this helpful?
Thank you for voting!
rack worn out and putting rust on dishes
1 person found this instruction helpful.
  • Barbara from Kansas City, MO
  • A Bit Difficult
  • 30 - 60 mins
took end caps off (one broke) slid in new disk rack and put caps back on.
Was this helpful?
Thank you for voting!
End of cycle water in bottom of nDishwasher
1 person found this instruction helpful.
  • Bonita from Alexandria, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed screen bottom rear andfound a plunger type part, unscrewed plunger and found it was distressed around it and did not close of a tight seal. Placed new part into location and dishwasher now proforms perfect...
Was this helpful?
Thank you for voting!
Pump/Motor leaking at shaft
1 person found this instruction helpful.
  • Brett from Sound Beach, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacem ent was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!
Was this helpful?
Thank you for voting!
leak between motor and pump housing
1 person found this instruction helpful.
  • kevin from longmont, CO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit
Was this helpful?
Thank you for voting!
Pump seal was leaking
1 person found this instruction helpful.
  • Buddy from Danville, IL
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
I disconnected the power shut off water supply. I then removed the drain hoses and water supply to the old pump. I removed the ground wire and the mounting rod to the old pump. Once removed, I followed the easy illustrated diagrams and instructions that came with the replacement pump.
I mounted the new pump using the supplied hardw are and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.

I would use this service again if needed for additonal home appliances.

Thank you
Mr. Buddy King
Was this helpful?
Thank you for voting!
Water would not drain out and keep filling up sprayers work
1 person found this instruction helpful.
  • Roberto from Key Biscayne, FL
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Your video doesn't include disconnecting water supply disconnecting electrical and disconnecting drain hose but after all that the repair to change the solenoid was a easy task but the problem was not solved so I TRIED . thanks Robert
Was this helpful?
Thank you for voting!
Difficult to install the mounting screws
1 person found this instruction helpful.
  • Edward from TUCKAHOE, NY
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Nut driver and philips screwdriver.
Was this helpful?
Thank you for voting!
Leaking at the valve
1 person found this instruction helpful.
  • Brian from DERRY, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench (Adjustable), Wrench set
Just like the video and replaced it
Was this helpful?
Thank you for voting!
water would not pump out of machine
1 person found this instruction helpful.
  • clyde from DUNCANNON, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I looked at your web sight and saw how to repair dishwasher.
Was this helpful?
Thank you for voting!
Hinge arm link wore out
1 person found this instruction helpful.
  • Samuel from LAS VEGAS, NV
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this helpful?
Thank you for voting!
dishwasher was not drainig completly after completing the cycles
1 person found this instruction helpful.
  • Chloe from Salisbury, NC
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Followed the simple instructions to unscrew the old unit and replace with the new one. The unit was easily located on a diagram on the internet and the website instructions for removal were spot on.
Was this helpful?
Thank you for voting!
All Instructions for the 36314779100
121 - 135 of 321