36314232100 Kenmore Dishwasher - Instructions

Replaced all ordered parts.

I removed the scews holding the inside door to the outside door section. Once removed I removed the 2 screws that held the switch to the door. After removing this switch I had to open it up to expose the four wires on the switch. I reattached the four wires to the new switch closed it up and placed it on the door with the 2 screws.
Replaced the inside door. Job finished with the switch working and the dishwasher operating as per the factory standards.
Very easy job and by doing it myself I saved money on a service call.

First I removed the four screws that secure the dishwasher to the underside of the countertop. Then I removed the four screws from the front cover at the toespace. Next I used an adjustable wrench to turn the feet to lower the unit enough to slide it out of the compartment. I unplugged the dishwasher and turned it on its side in order to access the hose chamber. I used a pliers to loosen the clamps at each end of the hose chamber and removed the the damaged item. Next I slid the ends of the new part into place and used the pliers to reposition the clamps. Finally I returned the dishwasher to an upright position, slid it back into the compartment, adjusted the feet to raise it to the proper height, put the toespace cover back on, secured the top of the unit to the underside of the countertop and I was good to go. No more water leakage.

Old baffles lift out and new ones installed - very easy

I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.

removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!

Ordered rubber connector and it arrived the next day. Shut off main power and water. Disconnected water supply and pulled unit out from under counter. Flipped unit over on it's side. Disconnected wiring, drain hose, clamps and completely removed motor/pump. Rubber connector would not unscrew by hand so I found a drinking glass slightly smaller in diameter than the connector inner diameter. Inserted glass in connector and proceeded to unscrew connector by turning connector and glass together. After removing old connector I cleaned the mating part after removing it from inside the washer and removed all the build-up. Replaced everything back in same order.

I used the website to identify a few different problem areas. I found that the motor shaft would not turn. Upon removing it, it did turn, which lead me to look at the Impeller which was worn / frozen. Ordered new impeller and installed 100 % success !!!

Repair is super easy and anyone can do it in no time!
At first my fear was that it was the pump, but after reading through the trouble shooting here it narrowed it down to the water inlet valve. The new valve even came with easy to read and understand instructions. I had it fixed in less time than it took my wife to make us lunch lol.

2 screws hold the mount bracket in place. Just remove the screws, remove the c-clip that holds the secondary/small water line on, pop the hose off then remove the main water inlet line [ its the bigger line with the brass fitting ] I only needed a pair of pliers for this. Reinstall the main water line into the new valve, but make sure you use pipe tape on the fitting or you'll have a water leak. Reinstall the secondary water line and reclip the c-clip using pliers to squeeze the clip. Hold the valve in place and reinstall the 2 mounting screws. That's it your done !!

This is the second time I've used partselect, and they are hands down the best !! Other sites would have you buying part after part until you happened to get lucky and get the right one. Not here, they help you figure out just what you need and nothing more.
Great people and fast service !!
Thank you once again.

The repairman offered to fix the dishwasher at a cost of about $200 or supply the water inlet valve for $85. Google led me to PartSelect.com where I easily found the correct part for $45. I received the part in 2 days by FedEx ground.
The hardest part of the repair was removing the dishwasher from the cabinet. I took the dishwasher out a short distance to the patio where I replaced the water valve...about 10 minutes.
I then made a makeshift connection to an outdoor water hose and connected the electricity and ran the dishwasher while out on the patio through a short cycle to make sure of the repair and check for leaks.
Then reinstalled into the cabinet...total time about 2 hours.
Thank you PartSelect.com

Unplugged unit, unscrewed screws on top of dishwasher attached to countertop, undid water supply and drain hose that goes into tee with garbage disposal. Using crescent wrench turned front leveling screws up all the way and slid/rocked dishwasher out from under the counter - I had no problem leaving back leveling screws down. Turned dishwasher over on some towels (it WILL leak some water so spread out some towels!) so it was oriented like the directions that came with pump and motor. The directions were good, although color or a picture might have been more helpful. CHECK the new pump/ motor unit CAREFULLY for any loose debris from packing etc. I had a small piece of plastic that was in the top of the motor that goes in the dishwasher bottom that rattled around after I installed everything and put it back. I was able to get to it from the drain assembly in the tub but it made a heck of a racket at first. All in all, I had a great experience. I'm glad I ordered the pump and motor even though I only thought I needed the drain solenoid because when I took the old unit out, the prop on the old impeller was almost gone. Easy to order, good customer service (I called with a question and talked to a wonderful customer service representative!), good directions and easy to do. I'd say a 4 out of 10 in terms of difficulty. Thanks PartSelect!

Took four screws out, unscrewed the piston & nut assembly by hand installed the new one. Cycled the dishwasher & it worked perfectly.

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

First I opened the package and screwed the new dispenser cap into place.