36314181202 Kenmore Dishwasher - Instructions

Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.

Unscrewed unit from counter and loosened legs using adjustable supports under dishwasher. After switching off water under sink and power at circuit breaker, removed motor and pump assembly and replaced with repair kit.

REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.

I had a problem where the GE dishwasher would randomly stall upon startup due to a dead spot in the motor which prevented it from energizing. I removed the dishwasher's bottom access panel to inspect it and found that not only was the motor dead but it had a sizable leak emanating from the pump seal. I removed the dishwasher from under th ... Read more e cabinet area and turned it over to make it easier to replace the motor and pump assembly which only took a matter of minutes; the most difficult part of the repair being the reinstalling of the dishwasher. The replacement motor/pump assy was not only modified from the original parts but it is also much quieter than the original. I also have to commend PartSelect on their very speedy delivery which was only 2 days. All in all with a couple of minor modifications that was taken care of with the included parts the repair went very easy.

Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before remov ... Read more ing them.

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

We bought a used dishwasher that appeared to be in good shape. After installing I ran it through its cycle. It seemed to work fine but after the wash cycle it would not pump out to drain. I found there was a solenoid that controlled the pump direction (drain or to the washer). It tested to see if it was getting power when it was supposed ... Read more to pump to drain and it was. When I manually actuated the valve the dishwasher pumped out as it was supposed to. With power to the solenoid and the valve working as it should the only peice left was the solenoid. I ordered it from PartsSelect.com and it arrived in 2 days. Installation was only 2 screws and a spring and all now works great.
The on-line parts diagrams and fast shipping make PartsSelect the only choice when buying parts for my appliances.

I replaced the drain solenoid which was about $35 dollars. It consisted of a couple of springs, a hanging bracket, a plastic part and couple of screws to fasten the bracket and the solenoid of course. My dishwasher now drains the water. Much easier fix than i thought it would be.

After checking to make sure the filter wasn't clogged I removed the faceplate and, poking around a bit realized that the solenoid that actuates the drain valve was jammed. Removing it was was simply a matter of removing a pin and two screws. I reattached the new part, the only difficult part was holding the part in place while reattachi ... Read more ng a few springs. Closed it up and its working like a champ.

I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.

Thanks for your help.

The repair wouldn't have taken as long as it did if the pictures on the installation sheet were clearer. They were very smudgy. Couldn't see the details on the pictures.

Starting removing the screws based on the Users guide document - was surprised to find 4 different types of screws and driver heads - Luckicly I am an adult male and have every tool -

the surprise were the Star screws - the phillips head and soctket screw were one thing -

Everything went well.

problem solved..thanks

I took the bottom plate off by removing 1 screw on each side. I then pulled the water inlet valve out, disconnected the 2 wires. Because mine was the original inlet valve and GE changed the new one I had to remove the new inlet valve from the face plated and use the old face plate. I then reveresed everything and put it back together and ... Read more Wah Lah the dishwaher was fixed!!

The finished accent panel on my GE dishwasher was dented and looked awful in my newly remodeled kitchen. I thought about purchasing a new dishwasher but instead searched the web for the part. Found Parts select and it was so easy to compare my part with the graph picture provided. Just count off the boxes for measurement and you will know ... Read more if you selected the part you need. Access panel arrived in two days,packaged well, and I am happy to have found this website. Give it a try....and returns are easy too if you make a mistake in ordering. My order was perfect on the firt try.