36314072795 Kenmore Dishwasher - Instructions

I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

first, I removed the screws holding the dishwasher to the countertop.Then I removed the dishwasher from under the counter. I turned the dishwasher on it's back and loosened the three hose clamps securing the water connections to the pump assembly. I then removed the electrical plug to the motor and the screw holding the support rod to the motor. Then I worked the loosened water connections apart and removed the pump and motor assembly.
Then I removed the hose clamp and plug from one of the orifices on the new pump, and aligned all of the water connections and wiggled the new pump assembly into place. I tightened the hose clamps, Installed the new screw and support bar to the motor, and connected the electrical plug. I then turned the dishwasher upright, reconnected the power cord, water supply and drain lines and started a wash cycle to check the new system for leaks. I found that the extraneous drain solenoid that came attached to the new pump was loose and rattling, so I secured the solenoid shaft and linkage to the pump housing with electrical tape to stop the rattling.

I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

Based on information gleaned from the internet, I suspected that the drain solenoid might have melted. I took apart the solenoid assembly and checked it out. I found that some of the plastic on the inside of the solenoid had indeed melted, making it impossible for the plunger that opens and closes the drain valve to move in and out smoothly and completely. I removed the old solenoid, replaced it with the new one, and the dishwasher worked perfectly.

Shut off circuit breaker to dishwasher and shut off valve to dishwasher under sink.Remove bottom access panel screws on both sides of panel. Remove both screws holding dishwasher to counter.Place old mattboard strips under legs to prevent scratching floor & slide out from under counter. Use a Shopvac to remove water and spillage. Have rags and paper towels handy. Carefully disconnect wires, drain hose and water line to free dishwasher. Fold old rug runner in half to place dishwasher on, turn on side and then gently upside down on rug to access motor. Remove butterfly clamps, hose clamps, electrical connections, and support bracket. remove old motor and pump and place in box to discard. Position replacement motor and pump according to diagrams. Reconnect all clips, hoses and connections. Since replacement motor and pump is smaller, use longer support bracket from adapter kit. Return dishwasher to upright position and reconnect wiring using wirenuts, drain hose and waterline. Reposition mattboard strips under legs and slide back into place. Attach screws to counter top. Turn on power, water and do a test run to check for leakage. Replace bottom access panel. Pat yourself on the back since you've saved yourself hundreds of dollars for a repair or replacement of your dishwasher.

Followed the instructions and it was easy. Made the washer seem brand new!...It is the best solutions for a small budget. We used CLR to wash out the washer workings and it really left a sparkle on the dishes... I am so glad you don't change the models so much that parts can't be exchanged when they wear...

I made this replacement more dificult because I removed the old motor/pump earlier. Should have done it at the time I installed the new unit to be sure all hoses where installed correctly. I hooked the drain hose to the wrong port and when I started the dishwasher I found my error. Once I corrected the problem and started it again - the wash and drain cycles were perfect and there were no leaks.

Disconnect electrical power & shut off water supply. Remove front panel covers. Removed mounting screws (2). Unhooked water supply line & flow line. Took off old brass adapter fitting. Teflon taped fitting to new inlet. Performed reverse procedures. It ran just fine!!

Removed built-in washer and turned on side. Removed complete motor and pump to work on bench (easier). Removed pump and replaced with new unit. Instructions did not tell what to do with white plastic tube for shaft(goes with lip facing motor onto shaft)Be sure rubber seal is pressed into pump fully. Inch pound instructions were not helpful. Remember how much pressure it took to take off it helps to install new pump. Inch pounds is not what most people know or use. Reassemble unit, flipped on end and tested for leaks before replacing under cabinet.

After determining the drainage issue was caused by the solenoid, (by process of elimination; the hose was clear, drain opening clear, diverter moving freely, power to solenoid present during rinse cycle= bad solenoid. Solenoid showed signs of overheating upon internal inspection...) I transfered the bracket assembly to the new solenoid, re-attached bracket to diverter reservoir, connected spring and power and Did a test run. Solenoid works great! I did notice the shaft on which the diverter pivots leaking just a bit while moving the shaft. You might consider oredering a new gasket for it if you plan to replace the solenoid. Pretty easy repair. Especially considering the complexity of some other possible problems! Good luck!

Before ordering the parts I read the posts by other do it yourselfers and found them very helpful. I ordered the seal and shaft nut from Parts Select and was impressed the parts were delivered in a couple of days. I removed the two lower panels from the dishwasher to expose the leak and the shaft. I turned off the electricity at the circuit breaker box and disconnected the wiring harness to expose the area I would work on. After cleaning the water deposits from the shaft I pried off the small lock washer and removed the plastic cam from the selenoid. Next step required removal of the push on nut. This was the most difficult part of the entire procedure. It required a bit of gentle but firm pulling with pliers and a couple of screwdrivers, sacrificing the nut in the process. It was better ordering a new one originally then trying to save the old one. Having experiencing these nuts in previous work, I knew a new nut would be a cheap fix! Once off, the old seal is easy to remove. Place the new seal on the shaft as per the included instructions, place the new push on nut and reassemble as originally taken apart. (I used a socket set to push on the push on nut.) I then ran a load of dishes to make sure there was no leak before reinstalling the lower panels. I had no leak but pay close attention to placing the seal and push on nut. The seal must be in the exact place.

I popped off the front track stops--pretty easy with a little twisting and slid the basket out. A little leverage with a screw driver and the roller axle slipped off easily. Popped the new ones on, slid the basket back into the track and popped the stops in place and the job was done in under 15 minutes.

First we got all the water out of the bottom of the dishwasher. Removed the old, melted drain solenoid. Very important - DO NOT THROW ANYTHING AWAY. The solenoid that removed was melted; however I had to reuse the springs, brackets and plunger from the old solenoid. I had to scrape and clean (with a solvent) the metal plunger to reuse it. Once I got it cleaned up and re-used the old parts, mounting it was easy. However, getting that tiny lockwasher on the shaft was a real pain in the ass. Finally I got it together and it worked great.

I ordered a replacement from partselect.com and received it in just three days. The only difficult part was deciding how to remove the white plastic end caps on the sliding rails. Finally, I took a small screwdrive and pried out the crimps in the metal, pulled the old caps out, inserted the new ones, and squeezed the metal together again using needle-nosed pliers. Nothing to it!
Note: The configuration of the new rack isn't exactly like the original (size and placement of the prongs differ somewhat) but it fits perfectly and works great.