All Installation Instructions for Kenmore Range 36272288890

old blackened oven racks

Replaced old with new.

Parts Used:

Oven Rack

Roger from Falls Church, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Only one burner sparking on range.

Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.

Parts Used:

Burner Spark Module - 120V 60Hz

Ronald from Freehold, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

6 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The bottom strip had become rusty and looking badly

I pulled the oven door off the hinges and took the bolts out of the bottom of the over that were holding the strip on. I then pulled the strip off and replaced it with the new on. I replaced the bolts and then replaced the door on the hinges.

Parts Used:

Oven Door Bottom Trim - Black

Carolyn from North Port, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven will not preheat. Pulses on an off.

Turned off the gas. Disconnected gas inlet, burner supply line and oven supply line from regulator. Unscrewed regulator from its bracket. Replaced with new regulator in reverse order and added teflon tape suitable for gas lines to all threads.

Unfortunately, the regulator was not the cause of the problem and the oven still does not prehead - acts exactly the same.

Parts Used:

Pressure Regulator

Paul from San Francisco, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable), Wrench set

7 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wife broke gas lines when trying to clean under hood

Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.

Parts Used:

Burner Tube - Left Front

Burner Tube - Right Front

Scott from Corinth, MS
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

lights blown out

replaced lights in refrigirator and freezer

Parts Used:

Light Bulb - 40W

Gerald from WINTERVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!

To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."

Parts Used:

Oven Thermostat

Leroy-Anthony from Jamaica, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

none

slid the old ones out and slid the new ones in. done

Parts Used:

Oven Rack

Michael from Laughlin, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven door gasket was missing.

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

Parts Used:

GASKET DOOR ASM

Eugene from TUSCALOOSA, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace Oven light socket and light bulb in kitchen Range

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

Parts Used:

RECEPTACLE PUSH-IN

Light Bulb - 40W

Ronald from TUCSON, AZ
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced igniter pins but no joy, needed igniter module

Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.

Parts Used:

Burner Spark Module - 120V 60Hz

Tim from NASHVILLE, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

A section of the gasket came off the door. It was causing heat to escape.

Found the Model information under the bottom drawer. Googled GE Range and rubber, found this vendor. Amazing, the replacement gasket was exactly as the original. Took the old gasket off with needle nose pliers, there were small metal clamps that had to be pinched together. Once the old gasket was off, the new one practically installed itself. Woman Power!

Baking is MUCH better now!

Parts Used:

GASKET DOOR ASM

Carol from Kansas City, MO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Digital clock no longer worked

No longer carry the one to our stove so it was substituted with Nafisa on it. You could see all the electronics so we had to pry the old face off the old one blew it in place, but a clock was reversed from timer, but it works.

Parts Used: