All Installation Instructions for Kenmore Range 36272231204

Needed extra oven space

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

Parts Used:

Oven Rack

noreen from flushing, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven post mini explosion sounding

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

Parts Used:

DEFLECTOR OVEN

Mchael J. from Chesterfield, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

13 of 22 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven bottom tray would not clean up.Looked like finish was off it

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Jim from 29 Palms, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

11 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

loss of spark to two burners, and bent orifice holder

unplugged the old spark module and plugged the new one in. Disassebled and reassembled the new orifice holder.

Parts Used:

Left Front Orifice

SPARK MODULE REPLACEMENT KIT

Kimberly from Leavittsburg, OH
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Wrench set

12 of 23 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Change bad/broken igniter on gas stove top burners

Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.

Parts Used:

Top Burner Spark Electrode

James from Kaplan, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

one burner would not light

opened back panel. noted location of colored wires. disconnected wires & removed module. attache wires to new module & attached module to panel. closed up back panel. tested all burners

Parts Used:

SPARK MODULE REPLACEMENT KIT

joe from malden, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

7 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Hole burned through deflector oven and metal dropped onto igniter and burned it out

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

Parts Used:

DEFLECTOR OVEN

Scott from ARDMORE, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt burner

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Parts Used:

Burner Head - Medium - 9500

Janine from Wind Gap, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven would not turn off due to inoperative thermostat

1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.

Parts Used:

Oven Thermostat

Timothy from Lake Elsinore, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old blackened oven racks

Replaced old with new.

Parts Used:

Oven Rack

Roger from Falls Church, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner on stove not working correctly

Order parts and installed - no tools needed - completed repairs less than 1 minute

Parts Used:

Burner Head - Medium - 9500

Trevor from Eldersburg, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!

To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."

Parts Used:

Oven Thermostat

Leroy-Anthony from Jamaica, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

none

slid the old ones out and slid the new ones in. done

Parts Used:

Oven Rack

Michael from Laughlin, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven door gasket was missing.

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

Parts Used: