Models > 36272220204 > Instructions

36272220204 Kenmore Range - Instructions

All Instructions for the 36272220204
91 - 105 of 137
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would lite but sounded like JET ENG.
removed 4 screws unplugged wires Then reversed prosseces
Parts Used:
Burner Bake Tube
  • Rick from Vanderbilt, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Open door. Put racks in.
nothing to it.
Parts Used:
Oven Rack
  • Harriet from Jacksonville Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Parts Used:
RECEPTACLE PUSH-IN
  • James from Monterey, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Stain/polyurethane dried on burner head & cap
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Parts Used:
Burner Head - Medium - 9500 Burner Cap - Medium
  • Stephen from Ogdensburg, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
open cook top / tubs pulled out front of stove
unplug power and turn off gas/// had to remove all star screws on top/remove ign wire from each burnner/now remove stove top/ adj wrench and remove nuts from the front nobs and relace with new front orifice tubes NOTE: Front orifice tube is the leftside. Front orifice HOLDER is the right side. put back top, open front to put hand in to make adjustments to ign wires close top and reinstall star screws and using finger to hold and make adjustments on top now turn power and gas on. I use soapwater to test for leaks/ leo gubin
Parts Used:
Left Front Orifice Front Surface Burner Tube and Orifice
  • Leo from Roseville, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
parts worn looking
No repair needed, just replaced parts. But the real story is that I ordered 6 parts and they came in 2 days. Five came correctly - one was wrong. One five minute phone call and the correct part came two days later. Never had such speed in delivery. And person I spoke with to correct the order was excellent. What a place to do business! Recommend it highly.
Parts Used:
Double Burner Pan - Left Side
  • Robert from Hyde Park, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Range tipped over in back of our pickup on way home from the store shattering the door glass
Followed the instructions I found on this site - it went really well - exception was trying to figure out exact slots for glass to fit in on top. Looks great!
Parts Used:
Outer Oven Door Glass - Black
  • Tracy from Nyssa, OR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Parts Used:
RECEPTACLE PUSH-IN
  • Patricia from Brandenburg, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
oven door seal gasket broken.
removed old gasket and clips, replaced with new gasket that came with clips. easy. worked well.
Parts Used:
GASKET DOOR ASM
  • Frank from Ventura, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
hole burned in oven burner tube. making noise
changed old burner tube , with new equipment. thanks to PartSelect.
Parts Used:
Burner Bake Tube
  • Rose from Edinburg, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven Heating Too Hot, More Than 100 Degree Beyond Setting
Replaced the oven thermostat and calibrated the new thermostat by adjusting the temperature setting knob. Instruction I found on-line were very helpful and the repair was moderately difficult. Trickiest part was threading the new thermostat into the oven. Total repair time about 1 hour.
Parts Used:
Oven Thermostat
  • Pamela S from Chesterland, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Large burner wasn't lighting very quickly
Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.
Parts Used:
Top Burner Spark Electrode
  • Jesse from Nashville, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Parts Used:
Oven Thermostat
  • david from harrisburg, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The oven door gasket was worn and didn't provide a good seal.
I use needle nose pliers to remove the old gasket tabs and clean the area with a scouring pad. Then I just lined the gasket up with the holes on the door and pushed the holding tab into the holds.Very easy and simple job.
Parts Used:
GASKET DOOR ASM
  • Willie from Selma, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Drip Trays lost finish due to use
Removed grates, lifted old drip pan, cleaned well and put new drip pans in. Simple and looks SO MUCH better!
Parts Used:
Double Burner Pan - Left Side Double Burner Pan - Right Side
  • Jeff from League City, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 36272220204
91 - 105 of 137
Back to Top