36272191891 Kenmore Range - Instructions

I removed all the burner heads with a torx driver & released the top of the stove by pushing in two clips with a screwdriver. I raised the top and located the thermostat as it fed through back of stove, then tied a line to the old thermostat to be used to pull the new one through. This did not work, so I removed a cover on the back of stove to provide more room & spread insulation apart so i could see hole. I was able to easily feed new thermostat through hole and reassemble.

Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Removed old gasket and pried out clips with screwdriver. Installed new gasket.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

While I was waiting on another part to arrive, I decided it would be a good time to do a thorough cleaning. When I lifted the top of the range, I lifted it to far and cracked both front burner tubes. The top of the range should not be lifted more than 4 inches without removing the 3 screws that hold each burner in place. When the new lines came in, I removed both front burners, knobs, and then removed the front plate behind the knobs using a Phillips screwdriver. The screws are located on the bottom of the plate. Using my adjustable wrench I replaced the lines. Then I CAREFULLY bent the gas tubes and remounted the burners. Over all an easy install. Just be careful, the gas tubes are aluminum and will break very easy. This is the second time I used PartSelect, and I am very satisfied.

This was a real easy job and a success,of course any repair i do on a gas appliance and when finished It doesnt blow up i consider a success.
Thank you,David Williams

I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.

Replaced old with new.

Took top off, removed wires from old spark module and put them on new one. Very easy and quick, works very well now.

Turned off the gas. Disconnected gas inlet, burner supply line and oven supply line from regulator. Unscrewed regulator from its bracket. Replaced with new regulator in reverse order and added teflon tape suitable for gas lines to all threads.

Unfortunately, the regulator was not the cause of the problem and the oven still does not prehead - acts exactly the same.