36271331202 Kenmore Range - Instructions

Popped off old gasket and some retaining clips stuck but were easily removable. New gasket pops right in, super easy. Fits like new.

The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!

Took it out of the box, lifted the stove lid and replaced the part, no tools required. Very satisfied with the shipping and the part, great service. Thanks!

You need to remove the knobs and remove the panel where the knobs are connected.

You also need to remove the display panel front to gain access to the where the electrode wires attach.

The other screws are readily visible. It's about 30 screws that need to be pulled.

The adapter put on the electrode can be pulled off with needle nose pliers and a small screwdriver, if the adapter does not fit through the opening on your stove. Just put the adapter back on after you snake the wires through.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !

Ordered the part and put it on. My husband hasn't relized that i took care of it yet. One day he might remember to ask if we ever got the part. Very quick delivery.

Simply removed old burners. Placed leveling nuts in place. Replaced new burners in place.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Simply took out old burners replaced them with new burners, no tools needed.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

I put it in the same way tuck it out

Just lifted off the old burners set on the new ones.

My husband and I probably could have done the repair in 15 minutes except for the difficulty lifting up the range top, dropping the screws into the range where they could not be retreived, threading the thermostate into the little holes from the top to the inside of the oven and then trying to hook the range top back into place. Even with all the difficulties we still accomplished the task in one hour. Thank goodness we had 4 extra screws that worked (actually only takes 2 but of the 6 we had, 4 fell into a place you could not reach into). Glue on the end of the screw driver finally kept the screws from falling into the black hole. It was an adventure and would do it again.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.