All Installation Instructions for Kenmore Range 36271112000

The pipe that carry the gas to the ignition part was damaged, therefore the burner was not lightening up.

Just have to remove the old kit and replace it with the new one. No tool required.

Parts Used:

Double Burner Assembly

Hyojin from Monmouth Junction, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old burners were rusty and broken

I just lifted the old part and dropped the new one in. Everything fits perfectly. The new flame is a beautiful blue color.

Parts Used:

Double Burner Assembly

Henry from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old burner assembly could no longer be cleaned

pop up range top. pull off old burner. put on new one.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.

Parts Used:

Double Burner Assembly

clare from north brunswick, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

one of the stove top burners had burned all the way through

matched part needed on web site; took off burner; ordered part; received it on the third day and easily replaced it. Wonderful, easy, and very short delivery time! Thanks.

Parts Used:

Double Burner Assembly

Brenda from Franklin, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken part

The key here was that I found the correcd part for an older kenmore oven and it was easily installed

Parts Used:

Double Burner Assembly

David from Warwick, RI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

We had to buy two dubble burner assemblies because one burner was out on each old assembley

The burner assembly was for my wifes daughter. She raised the top of the stove removed the old burners and set the new ones in place she also used the set washer and it works just fine.

Parts Used:

Double Burner Assembly

Alphonse from Glendale, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Deflector oven/gas flame deflector replaced due to hole melted from glowbar igniter

Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.

Parts Used:

DEFLECTOR OVEN

Barry from Coventry, RI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burners were not burning properly

Just removed the old and set in the new. Waalaa. All is well now. The web site, ordering, shipping and all was super easy.
Thank you

Parts Used:

Double Burner Assembly

Judy from Payson, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The double burner assembly had years of gunk so the burn was not clean.

The old double burners lifted off. Before the new burner could be set down into place, the area had to be completely cleaned using a flat blade screwdriver and damp rag. This allowed the new burners to seat properly in place. That is it.

Parts Used:

Double Burner Assembly

Larry from Forestville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Back burner not working

Lift stove top, rest it on the pop out holders on stove.
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]

Parts Used:

Double Burner Assembly

albert from La Veta, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Surface burner not igniting

I ordered the part I needed I recirived it overnite by 9 am.
I installed it in 20 min iwould have taken 5 min but the part was of such high quality I had to use a drill to make the opening slightly larger, very easy.the part I received was twice the quality of the original part. Thank You

Parts Used:

SPARK ELECTRODE TOP

PAUL R. from BOSTON, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

8 of 40 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Temperatures were much usually hotter than indicated

First of all I had to find the right part from Partselect, which was very easy, delivery was fantastically fast even tho I didn`t order special delivery. After reading installation suggestions on the website, it was simple, open the top, disconnect the burners, removed the thermo from the inside. The only hard part was threading the sensor through the correct hole. I had to remove a couple of cover plates to see where the hole was. Put it back together, lit the oven and the temps were correct, as shown by an oven thermometer.

Parts Used: