All Installation Instructions for LG Washer 31623

very dirty under adjitator cap and pulsator

Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,

Parts Used:

Pulsator Assembly

Daniel from EDWARDS, IL
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
Tools:
Wrench set

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

During the spin cycle water continued to flow into the machine.

unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.

Parts Used:

Washer Water Inlet Valve

Jim from Crystal Lake, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gave LE code

Former LG repair looked under washer while it was engaging & noticed motor was not spinning. LG took forever I ordered the part from you guys. It looked different from original. Figured out to take extra port for front loader. I have top loader. Installed washer works great!!

Parts Used:

STATOR ASSEMBLY

Michael from SAINT LOUIS, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Washing machine was displaying te code. Quick google search to diagnose the issue.

Very simple repair after watching YouTube video on how to complete repair.

Parts Used:

THERMISTOR ASSEMBLY,NTC

Richard from DICKSON CITY, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Washer pulsator was coming loose during wash cycle.

Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.

Parts Used:

Pulsator Assembly

Pulsator Cap

Kristen from Safford, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

could not get the 10 mm nut to loosen

Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had

Parts Used:

Pulsator Assembly

Marilyn from THOMASTON, GA
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drain hose had a pin hole leak external to washer

Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).

Parts Used: