2822A Frigidaire Range - Instructions

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. Stripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

wonderful went perfect!!!

Unplugged the oven
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together

followed the instructions that come with the part. very quick and easy.

could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!

took out the old (2 screws) put clip on wires and put the new part in. Simple

Replacing the faulty ignitor would have been simple enough if my arms were a foot longer and the bolts that secured the old ignitor had not been baked on.

With an ample dose of WD40 and some Vise Grips I finally got them broke loose. An Ohm meter can tell you pretty quickly if the old ignitor is bad. My old ignitor measured more than 1 mega ohm while the new ignitor read only about 346 ohms.

followed posted repair procedure on Parts select site. . . straight forward and simple. . .

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.

The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.

I simply searched YouTube for the problem I was having and foud it was probably caused by a bad part. I found the part online and ordered it. It was as simple as a few screws and a couple wire-nuts to install. My girlfrind was very happy to get the oven fixed !!!!
Thanks parts-select for having pictures and dimensions so I was sure I had ordered the exact right part.
I was soooo happy to have found you !

had the gas company do a free inspection.he told me the igniters go bad over time,so i went online with my model #and found a symptom/remedy page at part select.it said replacing the igniter fixed the problem 100% of the time.that gave me confidence and i ordered it,installed it and fixed it for $53.00(the gasman said most plces charged $250-300 to fix it.i was proud of myself-1st ever oven repair=great job!!! thanks.