2671532210 General Electric Washer Dryer Combo - Instructions

Replaced with the new part that I ordered from partselect.The washer works good. Thank you.

it was easy, it clip right on.needed to give it a little tap to get it in .

Thanks completely to the free videos on PartSelect.com. At first I thought it was the bearing at the rear of the drum. After ordering that part, I realized the noise was from the front of the dryer. I watch some more videos and decided it was the Front Drum Bearing and the 4 drum bearing slides. Parts were very inexpensive. The job took less than 15 minutes. Just had to remove the top dryer panel and pull out the front panel (with door) just a little to replace the front bearing. My dryer is now super quiet and like brand new again.

My dryer started to squeak so I checked several websites to fix the problem and found that PartsSelect was the most informative. The website easily directed me to the problem and provided me with the most likely cause. The top two issues for squeaking were the front drum bearing and the front drum bearing white slide. I purchased both and upon receiving the parts I watched the installation video which was very informative. After watching the video I realized that I needed two white slides and only one is in each packet. I went back online ordered the second extra white slide, two dark slides and the felt. Both orders were delivered quickly. The repair could not have been easier. All that I needed was a screwdriver and less than 30 minutes to do the repair. I found that both the white slides and dark slides were completely destroyed so I would definitely recommend purchasing both anytime you purchase the drum bearing.

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.

Removed gas line. removed control panel, removed top, removed front, removed burner, replaced igniter, put back in. paused and played the video. very easy to do. 42 minutes and I had a few beers.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

I unscrewed the front and top of the dryer. Removing the original front drum bearing was fairly easy, and just needed a gentle pull. The drum bearing slide was easily inserted in to the front drum bearing. Then the front drum bearing just needed to be inserted where the old one was removed. I did need some help from my husband to lift the dryer drum in order to close the dryer back up, but other than that, it was very simple.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

Good thing my husband is so handy. This part was very difficult to get to. Basically, he had to take apart almost the whole dryer. There is no access door so the side panel had to be removed, but before you could do that the front panel and door had to come off, then the top of the dryer. Keep track of the screws, we had a few leftover! But the dryer works great again and we hope to get several more years out of it. We've had no problems with it until now and it's over 15 yrs. old.

watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.

I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes