2537034241J Kenmore Refrigerator - Instructions

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

Basically the only tool you need is a screwdriver to remove two screws on the trim piece and then the screws on the dispenser unit. This is where the patience comes in. Don't force anything or you'll be buying a new unit again. The tolerances are very close and the tubing for the water needs to be removed from the brackets carefully. Pay attention where the wire connectors go since you'll need to plug in the new ones. From there, just put things back in reverse order and close it up. I'm fairly good with tools and figuring out how to repair things, but I gotta tell you, this is really easy. Don't be afraid.

Removed two screws and disposed of two broken tabs holding old trim in place. Placed new trim in place, fastened the same two screws. Done.

About two minutes.

i put casket on i notice when i received casket in shipping box was bent on the end of the casket 's did not solve problem casket not flush air is due to damage from shipping in the box not happy with the product.

Basically unhooked water lines and removed the screws

Located problem part of ice maker on web site. Picked the part that had the highest percentage of being the the part that was broken (58% I think). Removed the part, waited for the new part, then put it all back together. Simple. It works great. Thanks for having such an easy web site to diagnose the problem.

Remove the freezer drawer by unscrewing the two 12mm screws on both sides of the drawer.
Lift the drawer up out of the slots the frame and away.
Lay the drawer on a padded surface to protect the drawer cover finish.
Pull the old gasket out of the drawer and discard.
Position the new gasket around the edge of the drawer. Starting at one corner press the gasket into the slot in the drawer edge. Continue working the gasket until you return to the starting point.
Inspect the gasket to ensure it is seated in the slot completely.
Return the drawer to the refrigerator, placing the lugs on the drawer into the slots of the frame and insert the screws to their original position and tighten securely.
Inspect the drawer for proper level/sealing in the freezer drawer position. Adjust as necessary.

Snapped the new shelf in.

VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT

I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.

Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.

Simple tightening of the screw with the right tool.

Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.

Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.

remove drawer , remove top shelve remove and repleace side rails ond take rollers off and repleace rollers. not bad at all