25360137990 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
End caps broken - shelf kept falling off
Snapped the end caps onto the existing shelf, and eased the assembly into the door slots. Light tapping with a hammer was required to fully seat the assembly into the door. All in all, a straightforward and simple repair.
Parts Used:
-
Barbara from Gaylord, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken shelf clips
snapped in the one end, placed the bar in one end and the other clip on the other end and snapped it in place.
Parts Used:
-
Donald from Spencer, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Meat drawer kept falling
I removed the screws from the old rail, which was broken, and installed the new rail using the old screws. It was very easy, and I wish I had fixed it months ago when it first broke.
Parts Used:
-
Thomas from Batavia, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken plastic pieces
Removed the old support bar which was broken, stuck the new one in, and adjusted the height. Fit perfectly.
The crisper draw cover supports were stuck in the frame. I used a screw driver to pry them loose. The new ones fit in perfectly, and voila - a perfect fit.
Refrigerator door shelf bin snapped into place with no problem.
Very satisfied with the time to receive parts, time to do repair, and final outcome. Would definitely order from you again.
The crisper draw cover supports were stuck in the frame. I used a screw driver to pry them loose. The new ones fit in perfectly, and voila - a perfect fit.
Refrigerator door shelf bin snapped into place with no problem.
Very satisfied with the time to receive parts, time to do repair, and final outcome. Would definitely order from you again.
Parts Used:
-
beth from brooklyn, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper cover support Bar was broken
Put glass in the new crisper cover and the support bar in place.
Parts Used:
-
Patricia from Eupora, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Parts Used:
-
Larry from Newton, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My grandson pulled the drawer down,and broke the rail.
The repair took less then 15 minutes,my husband put the new rail on,he used a screwdriver,now I have a folder just for partselect/fridge.My
grandson is 4years old,and he can do some stuff.
Thank You
It came within 5 days.
grandson is 4years old,and he can do some stuff.
Thank You
It came within 5 days.
Parts Used:
-
DEBORAH from BALTIMORE, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The refrigerator light would not work ...even after replacing the bulb.
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Parts Used:
-
TIM from WOODBURY, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Getting the light socket to snap back in properly
-
Robert from HELENA, AL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Brokern Door shelf end caps
The door shelves in the freezer door of my Frigidaire refrigerator were broken, rendering the shelves useless. I ordered four (4) end caps from PartSelect. The end caps arrived in about five days. I attached the caps to the ends of the door shelves and popped them into the slots on the door. It was a very easy repair!.
Parts Used:
-
Jennifer from Cleveland, TN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
freezer worked frig was warm. Ice maker is still not working
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall
Parts Used:
-
steve from Kirkland, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Parts Used:
-
EDWIN from ELWOOD, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unable to use shelf because retaining bar bracket broke.
Cleaned insert hole, did a dry-run, then pressed everything permanently in place.
Parts Used:
-
Robert from Chicago, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer built ice, fridge not cold enough and running constantly.
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
Parts Used:
-
LUIS from CENTENNIAL, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coil Iceing up
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .
Parts Used:
-
Thomas from Stuart, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!