25358689891 Kenmore Refrigerator - Instructions

Used exploded parts view to locate part. Removed old part and replaced with new defrost timer. Piece of cake.

You have to blindly unscrew the two screws along the side of the ice maker. Once that is done simply remove the ice maker to the side to gain access to the electrical plug. Undo the plug and remove the ice maker completely. Install the adapter on the new ice maker and install it in much the same way you removed the old. I started the (2) 1/4" screws before installing the new ice maker to make it easier to hang. Pay careful attention to the wire harness and dress it out of the way. Finally tighten the two screws and make sure the bail wire is down to begin ice making once again.

this repair was easy.just screw off the cap and the filter is inside and put new filter in the cap and replace.that is all there was to it and i was glad i could do it myself.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation

I purchased the replacement part (no instructions sheet) from another company, not this one, that cost 2X's a much as this company. So I sent it back and ordered from this company. Got it faster then the post office sends us the stamps we order by internet and this ice maker had instructions.
Our's is a side by side refrig, so working space is limited but do-able. The old ice maker has made a clicking noise for years while trying to push the cubes out of the tray. They would get stuck and refreeze, sticking half way out of the tray.
I loosened the 2 screws with a socket driver (which are difficult to see), raised the unit up and off the screws. Unplugged the power & out it came. Removed the bracket on the side as instructed to attach to the new ice maker and in the trash the ol' ice maker went. Set the new ice maker on the screws, plugged in the power, tightened the screws and walla. A quiet ice maker. In fact, it would startle us the first day as we didn't hear the clicking noise indicating it was stuck. All of a sudden the cubes just dropped into the container. Alright! Don't know why I didn't do this years ago.

I want to first say that before I ordered this part from "Part Select" I first went and talked with a local appliance repair shop. They quoted me a $120 charge to come out and check the problem. Then $30 and hour service fee, plus parts. He provided me a quote of about $250 for the job.
I found this part easily on the web site $77. It was very easy to instal. The only problem I had was the fact that in the side by side it was very difficult for me to get two hands inside the freezer to install it. (I have wide shoulders). Two screws loosened, no need to remove them. Just life the entire unit straight up. Unplug wire harness. Then just reverse order. Could not be easier. If you can change a light bulb you can do this.

Noticed no cool air was coming from the vent on the refrigerator side. After cleaning out the freezer side, I noticed that the air intake at the bottom of the freezer was frosted over.I removed the metal panel and discovered the coils were completely frosted over so I found the defrost timer located at the bottom left corner of the refrigerator. took a screwdriver and turned it very slowly to force a defrost. i watched the coils for awhile and noticed that the heat element would never deice. so I thought it may be the thermostat clamped to the top of the coil might be bad. I unplugged the thermostat and plugged the heat element coil directly to wires feeding to the thermostat. On my refrigerator the wire connectors will allow to bypass thermostat. After waiting twenty minutes, I forced another defrost cycle with the timer and noticed the heat element would still not defrost. So i unplugged the heat element and took a test meter and checked the wire connectors and found one twenty volt at the connectors. So, therefore, I determined it must be the heat element itself. Even though they rarely give trouble. I found the service diagram on the back of the refrigerator in a plastic pouch, and it said the ohm resistance should be twenty two. My element read 145 so that also pointed to a bad heat element. I took the screw out that holds the coil in, lifted it about two inches, and pulled the bottom of the coil out just enough to remove the heat element from the coil and discovered it had a crack in it. It must have been a Monday at the factory, because the heat element looked like it had been warped while being installed.I ordered a replacement element and installed it. I works as good as new. I do electrical work for a living, so this was pretty easy for me to figure out.

Removing the old unit was easy enough, just loosened two screws that attach unit to side of freezer and disconnected the wiring harness. But the new unit never goes in quite as easily because it's always just a little different from the original. In this case, the wiring ended up being about six inches longer and the excess had to be stuffed behind a shield at the rear of the unit. Theoretically, the wire could have been pushed back through the opening, but it got jammed and wouldn't go. I had to remove side rails and pry the shield forward in order to get the wiring back out of the way. The unit is a narrow side by side, so there wasn't a lot of room to move around. But it wasn't difficult, just tedious. I had to make sure the wiring did not come into contact with the heating element at the bottom of the icemaker. Once installed it worked great.

since there are two(2) water inlet valves, had a 50/50 chance of getting the right one,since the water dispenser worked ok, by the luck I replaced the wrong one first, with the part I took out I rebuilt the other valve which was the bad one, put the rebuilt valve back in evertthing was good to go. Had water again.

Followed the steps in the video on your site, really easy to do.

un plug fridge. removed ice maker from fridge. loosen 2 mounting screws. lift unit in slots to get over heads of screws. unplug wire harness. remove cover. remove 3 screws from control housing. remove 2 motor mounting screws. unplug motor wires from switches w/needle nose. installation is the reverse. plug in fridge turn on icemaker. takes 10 to 15 min to start to cycle.
easy and cheaper than new fridge or ice maker

I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.

Popped off the front plastic cover on the bottom of the fridge, under the doors. Two screws held the defrost timer on under the front side of fridge (below freezer door). You can't really see the timer except for the adjustment knob that is accessible through a hole. Once the screws are removed, disconnect the wire plug and remove and replaced unit. Works fine ever since.

I removed an access panel loosened the two screws that was mounting the water valve to the refer frame. I took off the three lines to the valve and unplugged the wires from it and reinstalled the new valve. The whole job took 5 minutes.