25354363403 Kenmore Refrigerator - Instructions

Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.

The biggest part of the repair was getting everything out of the shelves in the door. I had to remove one phillips head screw from the plastic hinge cover on the top of the appliance. As per the owners manual I traced around the hinge with a pencil so I would be able to align the door to the same postion. Removed two screws with a nut driver and removed the top hinge. The magnetic strip held the door in place until I grabbed it and pulled it open then lifted it up off of the bottom hinge. I layed the door on the island counter and pried the bearing hinge out of the door stop and replaced it with the new one. I probably could have stopped there but figured the plate might have been worn so I remove one phillips head screw from the bottom hinge, lifted the plate off, and replaced it with the new one. I assembled everything in reverse order and voila, no more popping noises.

take out screws front control panel ,then screws on left panel holding control unit. had to clean up plastic she got a little toasty. unhooked control unit replaced with new and reassembled. The real story is in your excellent web site easy to find exactly what I need and with prompt shipping, I was back in service quicker than having someone come out and repair.

Great Job
Jeff Baker

Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.

Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.

-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.

After earlier determing that the starter switch was at fault, I removed the cardboard lower back panel, shut off water to the ice maker, removed water line. The plug to the compressor containing the switch and capacitor was held on by a spring clip, removed clip pulled wires from old switch (Here needle nose pliars are handy as the spade clips on the 2 wires have their own locking clips) replaced switch and all wiring, tested unit and problem solved.

I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.

The ice maker would over floew then not cycle it would freeze with the forks stuck in the ice! so just get your modle # and serl, # call in and order the hole ice maker it cost only about $120.00 with shipping!! it is so simple to put in just lossen the 2 1/4 screws in the back and lift up then unplug it. you do not have to turn the water off as it works off the pump at the bottem !!( note you nedd to take the ice bucket out it just slides right out !! You will save the service call from A repair man it is really very easy so by the time it took to read this you will have it done !really its that easy!!

I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

I found that getting the water/ice dispenser back in place was the hardest part because the water hose is so short. I finally threaded a stiff wire up into the hose and guided it through the dispenser opening. The rest was pretty much routine.

The broken fan made my refrigerator sound like a lawn mower I pulled the refrigerator out of it's nook and disconnected the power, removed the back panel with my battery powered drill motor, slid the old fan off of motor shaft, slid the new fan back on ran it to make sure the problem was corrected. The entire repair took less than fifteen minutes and was as simple as it could be. Please be careful when cleaning your coil, as the fan is easily damaged if you should contact it.

The most difficult part was the removal of the existing fan and shroud. There is very little room to work between the condenser and the coils where the fan is located. The old shroud had to be removed as it was not compatible with the mounting for the new fan motor and blade. Make sure to unplug the refrigerator and give the coils some time to cool down. The first step was to remove the old fan blade... it simply pulls off. Next you need to remove the two bolts holding the fan shroud to the floor of the refrigerator. Then you need to remove the old fan motor from the shroud... unplug the wire connection and remove two small bolts that hold it on. I was lucky to have a VERY small ratchet to get into these tight spaces. Now is the really hard part, removing the metal fan shroud takes a lot of twisting and turning to get it out. The coils have a little play in them, but you must be very careful of the tubing and connections. Also, the coils are very sharp. Once this is out, IF you can get it out....I had my doubts along the way, you can start to put the new parts in... beginning with the new fan shroud which fortunately is made of plastic and has some give which makes it easier to get in. Then you can mount the new motor to the shroud with the three new screws. Plug in the wire connection, add the foam tape to the shroud and mount the shroud to the floor of the frig with the original two bolts. Lastly, attach the fan blade. This replacement kit is well constructed, fits perfectly and contained all the necessary parts (fan motor with wiring connection, mounting screws, wire connection adapter, fan shroud, foam tape and fan blade), but no detailed instructions come with it. I was lucky to get the old fan shroud out without doing any damage to the surrounding parts, but this part was very difficult for a do it yourself person. I would be interested to know if a professional has some other tips for this part of the replacement process.

A plastic guide rail broke after the meat keeper drawer was left open and the refrigerator door was shut on the drawer, this has happened a few times over the last 6 years. We chose to change out both rails at the same time. We removed the meatkeeper drawer, then the shelf above as the rails are attached to the shelf. We removed the rails (one screw on each side. When the new rails came in, we replaced them with the screws. Super easy!

Pulled the drip tray out of the ice/water dispenser.
Removed 3 screws, pulled up the beauty ring.
Removed 3 more screws, pulled out the circuit board, and plastic plate that it is installed in.
Removed screws that hold the actuator in place. Unplugged and removed broken actuator, installed new actuator, installed hold down screws. Plugged in actuator. Installed beauty and other parts in reverse of removal. Would probably recommend removing door handle on the dispenser side. Would make installing one of the screws much easier. But you have to remove 2 small hex screws to remove handle.