25350683001 Kenmore Refrigerator - Instructions

Used pliers to remove filter.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

I followed all the usual suggestions about changing the water filter and disconnecting the exterior copper line and testing it to make sure flow was steady. I then got ambitious and diconnected and tested the flow of water through each of the refrigerator's interior valves. Isolating my problem inside the dual valve that regulates feed into the water dispenser and icemaker I was able to clear out the blockage with a small dustbuster air cannister but reassmbling the valves somehow caused the valve to no longer function right so I ordered a replacement valve and had it all reconnected in five minutes once the part arrived. A simple repair to avoid a very costly replacement! Partselect has now been used by me to repair my oven, refrigerator (twice) and microwave. A pretty good alternative to replacing an appliance if you are willing to try your own repair.

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

Twisted replacement bulb into place easily. Let there be light!

Turned off water and unplugged refrigerator. Removed rear cardboard pannel. Removed screw holding valve, unscrewed water lines, disconnected wires. Drained excess water into cup. Reinstalled lines on new valve. Reconnected wires. Installed into place. Reinstalled cover. Done. Wasn't sure if this was the problem but narrowed it down to a few things. Valve wasn't closing all of the way allowing water to continue to drip into ice maker and out door. Works perfectly. Oreder on Sunday received by Tuesday. No complaints for PartsSelect.

I order part # PS429001 dual inlet water valve located in bottom left corner of refridge on monday it arrived nest day.I then shut off water source and disconnected refridge.
I removed back bottom panel { 5screws} and then i removed
water valve {1 screw} I unplugged electrical wires and water feed lines from valve.You have to pull hard on feed lines to remove. I installed new valve, connected wires,
i had to clip off about 1/2" of feed line ends for a tighter fit on new valve. I reinstalled back panel. I plugged in refridge turned on water,and presto i'm getting
fast water again from the dispenser. P.S. I also took the time to vacumm around compressor and fan.
thanks PARTSELECT.

The longest part of replacing the drawer was swapping all the veggies out of the old one. No tools,slid the glass drawer front from the old one and slid it into the new one.

I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.

I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.

I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!

Pull refrigerator from wall and disconnect the water line and unplug the power.

On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.

Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..

Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.

Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.

In about an hour you should have ice filling the bin. Enjoy!

After posting the specific symptoms and getting feedback, I had narrowed the cause to two linked parts. I ordered both intending to replace first one, then the other as needed. With parts in hand, I pulled off the freezer control knob, used a nut driver to remove the two panel securing screws (behind the face, against the inner ceiling) and gently dropped the cover down. The control (temp sensor and cold control) is easily accessible as it sits wedged into two slots in the plastic cover. The control must be slightly lifted in order to extract the long sensor that attaches to the control and runs under it and into a plastic sleeve behind the panel (the new control comes with the sensor wrapped in a tight coil and it must be unwound for the install). Removed the three wires noting which color goes where. Used needle-nose pliers to remove the small push-on tabs and removed the control. After starting the new sensor probe into the sleeve re-attached the 3 wires to the new control. Used the original as a model for how to pre-bend the probe for the first 2 inches as it was mildly frustrating to position the unit back correctly. Pushed everything back into place, re-installed the screws and plugged the fridge back in...(you DID unplug it first, right?). Still haven't used the second part (defrost timer), but I expect it to go soon...it is a 17 year old refrigerator, after all.