253331809108 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Gasket was not holding tight and I replaced with a new one.
-
Kebreab from NASHVILLE, TN
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer and refrigerator stopped cooling
The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.
Parts Used:
-
Amy from PITTSBURGH, PA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
8 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was missing a shelf when we moved in
-
Steve from Raleigh, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
13 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door shelf bar broke
This was a really simple repair. The hardest part was getting the broken piece of the plastic end cap out of the metal retainer bar. I had to use a small screwdriver to gently pry it out of the two notches in the retainer bar. Then I just slipped on the new part, and snapped the whole retainer bar into the fridge door and that was it.
If the end cap doesn't lock into place when you slide it into the metal retainer bar, you may need to bend the bar (gently) to get the notches around the plastic clips. You don't need a lot of force to do this since all you want is to lock the end cap in place.
If the end cap doesn't lock into place when you slide it into the metal retainer bar, you may need to bend the bar (gently) to get the notches around the plastic clips. You don't need a lot of force to do this since all you want is to lock the end cap in place.
Parts Used:
-
George from Worcester, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked drawer
I slid out the old drawer and slid in the new drawer. Easy as that! I would recommend this website to anyone.
Parts Used:
-
Jaime from Harrisburg, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch would not allow door to close.
Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!
Parts Used:
-
Charles from Front Royal, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lightning struct the house and fried the evap thermostat
Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now
Parts Used:
-
charles from parker, CO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
8 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no problem just added ice maker
insatlled ic maker was very eays and fast.how ever not enouh clamps for hose;s in kit in my apinion
Parts Used:
-
eugene a from sycamore, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench (Adjustable)
35 of 93 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bought a new refrigerator. Did not come with an Icemaker.
Remove access cover at bottom of case w/socket wrench (4 screws).
Attach supply line to water valve with adjustable wrench. Attach water line to ice maker on back of case (twist lock) no tools required.
Attach water line from ice maker to water valve (push connection) no tools required. Attache water valve to case at bottom w/one screw. (nut driver)
Reassemble access cover to bottom of case w/socket wrench (4 screws). Remove plastic cover inside freezer (w/screw driver to release from evap cover) to expose ice maker harness connection. Remove two plastic plugs (carefully w screw driver) exposing screw anchors for mounting Ice maker. Assemble two mounting screws w/nut driver. (Do not dtrive all the way in) Plug ice maker harness to plug on back of evap cover.(no tools required) Place cover over harness connection) no tools required. Guide water fill tube into fill cup on ice maker. (no tools required) Hang ice maker on mounting screws. Level Ice maker and tighten screws. (torpedo level makes it easy if you have one handy. Place Ice bucket under Ice maker on freezer shelf (lower position). Turn ice maker on and you are ready to go. Easy Job!!!!
Attach supply line to water valve with adjustable wrench. Attach water line to ice maker on back of case (twist lock) no tools required.
Attach water line from ice maker to water valve (push connection) no tools required. Attache water valve to case at bottom w/one screw. (nut driver)
Reassemble access cover to bottom of case w/socket wrench (4 screws). Remove plastic cover inside freezer (w/screw driver to release from evap cover) to expose ice maker harness connection. Remove two plastic plugs (carefully w screw driver) exposing screw anchors for mounting Ice maker. Assemble two mounting screws w/nut driver. (Do not dtrive all the way in) Plug ice maker harness to plug on back of evap cover.(no tools required) Place cover over harness connection) no tools required. Guide water fill tube into fill cup on ice maker. (no tools required) Hang ice maker on mounting screws. Level Ice maker and tighten screws. (torpedo level makes it easy if you have one handy. Place Ice bucket under Ice maker on freezer shelf (lower position). Turn ice maker on and you are ready to go. Easy Job!!!!
Parts Used:
-
MICHAEL from GEORGETOWN, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench (Adjustable)
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven light bulb went dark; it needed replacing
-
Lise from CEDAR GROVE, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
9 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Evaporator fan motor quit and would not circulate cold air from coils.
Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.
Parts Used:
-
Denver from BLAIRSVILLE, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door retainer bar end broke
The plastic ends are held to the retainer bar by small metal tabs in the retainer bar. Pry up the tabs to remove the broken part. Insert the new part and crimp the tabs back down with a pliers. Couldn't be easier.
Parts Used:
-
James from Austin, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
freezer frosting over,fridge warm
removed ice maker,,and screws holding back of freezer cover,unplugged wires and removed the cover and fan.wow,only wire to element had come unplugged!went ahead and replaced thermostat,and defrost timer,both were easy to do
Parts Used:
-
Brian from Otterville, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
8 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer compartment warm / Ice cream soft
I worked for GM as a Frigidaire Tech, before starting my own business. I have retired now.
I took the three screws off the back of the bracket holding the motor. Disconected wire harness and pulled out the motor. Reverse to install. servantoftheking@hughes.net
I took the three screws off the back of the bracket holding the motor. Disconected wire harness and pulled out the motor. Reverse to install. servantoftheking@hughes.net
Parts Used:
-
George from McBee, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
8 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unit quit cooling
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.
Parts Used:
-
Steve from Cedar Park, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!