25331422101 Kenmore Refrigerator - Instructions

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

A little difficult getting out due to restricted space, I took off the fan blade, that gave extra working room. Then it went well going back together,and it all worked as advertised. Thanks. p

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though ... Read more it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Turned off fridge circuit breaker
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker< ... Read more br />Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.

You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fas ... Read more t and easy, door opens and closes smoothly and no problem with condensation anymore.

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the cop ... Read more per refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

Just had to pop the old pieces out, assemble the new ones, and pop them in. Very easy. Anyone can do it.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

The refrigerator that came with the purchase of my house had a missing retainer bar in bottom shelf of fridge and a duct-taped retainer bar in freezer. When parts came, all I had to do after removing the duct-tape, was slide up the broken end cap to pop it off then, snap the retainer bars into the end caps and slide them down into place. ... Read more No tools necessary. Should have done this two years ago when I bought the house!

Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.

I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!

I also want to say how FAST PartSelect gets their items to you. It came in ONE day!

Your repair stories ar ... Read more e very helpful, I/we would have never known how easy this switch was to replace! Thank you!

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.

I watched brief video on your website.