Models > 20131 > Instructions

20131 ((1988)) Kenmore Range - Instructions

All Instructions for the 20131
1 - 12 of 12
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Parts Used:
Light Bulb - 40W
  • Barbara from BELLEVUE, WA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    Less than 15 mins
14 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior light needed replaced
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Parts Used:
Light Bulb - 40W
  • Leo from TWIN FALLS, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
14 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lights blown out
replaced lights in refrigirator and freezer
Parts Used:
Light Bulb - 40W
  • Gerald from WINTERVILLE, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
Parts Used:
Light Bulb - 40W
  • Catherine from SEATTLE, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Parts Used:
Light Bulb - 40W
  • Roscoe G from ROCHESTER, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change bulb
Easy
Parts Used:
Light Bulb - 40W
  • Louis from LEAGUE CITY, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old trim rings were rusted and soiled
Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.
Parts Used:
Trim Ring - 8 Inch Trim Ring - 6 Inch
  • Stephen from Bridgton, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old and corrosive due to age
After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed
Parts Used:
Trim Ring - 8 Inch Trim Ring - 6 Inch
  • Donald from McConnells, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed to replace drip bowl and trim ring
The replacement drip bowl and trim ring fit perfectly.
Parts Used:
Drip Bowl - 8 Inch Trim Ring - 8 Inch
  • Stephanie from Kitty Hawk, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I needed new trim rings around the stove burners
I logged into GE's website, put in my stovetop's requirements for size and type of trim rings, and was taken to partselect's site where I found what I needed. I ordered it and it came in less than a week!
Parts Used:
Trim Ring - 8 Inch Trim Ring - 6 Inch
  • KoLynn from Tempe, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original trim ring did not fit
I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.
Parts Used:
Trim Ring - 6 Inch
  • Sarah from San Andreas, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Solenoid failed due to excessive heat.
Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.
Parts Used:
Door Latch Solenoid
  • Joseph from Martins Creek, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 20131
1 - 12 of 12
Back to Top