1J2442M2 General Electric Range - Instructions

1. remove two nuts on rear of oven wall.2. remove 2 screws holding connection to element. 3. attach element to oven wires w/ 2 screws. 4. reinstaill 2 nuts to oven wall. 5. Test oven.Make sure power supply is disconnected @ electrical box!

Shut off breaker to oven. Removed two screws holding the element. Removed two wires attached. Cut back old wires and crimped on two new eyelet terminals. Screwed wires onto element and reattached. Turned breaker on and tested. Works great. Any girl can do it.

got new part delivered two days after ordering. I turned off breaker, used a 1/4" wrench to remove the fasteners holding the heating element to the back inside wall of the oven. used screw drivers (one Phillips and one flathead) to remove the screws holding the heating element to the wires. ensure you pull the wires slight out (easily) to ... Read more ensure they don't pull back into the oven wall. unplug the element from the wires, install new element in reverse fashion and voila, done.

Removed the element and put in a new one. Screw mounted interface to 230 mains involved removing two screws in oven wall and two connecting the main wires. Screws were provided with element. Effortless replacement saved an expensive house call and/or oven replacement. Oven is 44 years old and Parts Select had an original replacement p ... Read more art here in 4 days at new years. Part was only $18.45. Parts Select rocks!

Ordered new element (super-easy to select the right one at this site!). Turned off stove breakers. Removed two screws holding mounting hinge plate with nutdriver. Detached wires with regular screwdriver. Attached wires to new element lugs with screwdriver, using furnished new screws. Reinstalled element hinged mounting plate with screws a ... Read more nd nutdriver. Only difficulty is 1) working bent over inside the oven because the wires are short, and 2) wire screws are regular, not Philips, with shallow slots so screwdriver slips out frequently.

removed two screws with nutdriver, removed two screws attatched to element. reversed procedure. this took less than 15 minutes. "remember to turn turn off power" Jeff

replace old one with new one thank you.

I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connectin ... Read more g the 3 wires, I reattached the element to the range.

pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.

The repair went well and once again my stove that was installed back in 1968 is working perfectly. We will be buying another 6" burner and 2-8" so we have them when they begin to burn out. We looked everywhere for a replacement and was told they do not make them anymore, but we found it here. Thank you!

Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!

It was easy and worth doing myself because a repairman said, he could do it for $50.00 dollars. I spent $28.00 which includes the shipping cost.

Delivery of the replacement element was quick.Two days after I ordered. My husband replaced it and said it was easy. He just had to unscrew the old element and disconnect the terminals on the back.I thought I was going to have to buy a new stove,just because my oven element wasn't working. Many thanks!

--ordered part on line ---It came in the next day without any extra charges for over night shipping! The whole thing with shipping was about $26 and so easy to install. Turned of circuit breaker, unscrewed element and screwed in new one.I was so impressed with 'Part Select'. I have never had a more efficient and inexpensive experience ... Read more with online shopping. Thank you , I would highly recommed you to everyone! Dee

First, I turned off the power at the breaker box. Then, I removed the 2 screws attaching the bake element to the back wall of the oven. Next, I pulled the element out a few inches and removed the screws holding the element to the wires at the rear of the oven. Finally, I reattached the new element to the wires with the screws and then ... Read more reattached the element plate to the rear wall of the oven. I turned the power back on at the breaker box, and tried the new element. It worked! Also, shipping was real fast, like 2 days from the time I placed the order to receiving the element.