19864 - Instructions

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

Very slowly, had no clue what I was doing. Instructions were great, and even I got the job done.

After trying to clean and use chemicles to remove residue, I found that it would not work. Ice would build up in tray causing an overflow in the fill process. this would freeze cubes in tray below causing dispenser not to work properly, New tray seemed to solve the problem. Removed old and installed new

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Just took old ice tray out and put new one right in place in less than 30 seconds. I am very pleased with how fast the tray arrived after being ordered. if only everything ordered could be made this simple. You are a great company to deal with.

I tilted the unit back enough to scew the new legs into the threaded holes.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabine ... Read more t on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.

Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.

The Whirlpool water inlet valve was better design than the original. All I had to do was drill 2 holes to mount it since it didn't mount in the same location as the old one. I liked the push in connection for the water outlet to the ice maker better than the original plastic screw connection.

Replaced the valve and cleaned all the coils at the same time. The ice maker is spewing out ice. Wife is happy again.

Removed old water valve on bottom right back side of fridge installed new one which actually took less work

Reattaching the kickplate clip was easy, but the tab that holds in place was broken. It would slide back when the kickplate was installed. I fashioned a replacement tab out of a piece of 3/32 aluminum bent into a U with the hammer. To hold it in place I drilled and tapped one hole and used a 6-32 machine screw.

Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice ... Read more maker. Gregg in PA.

unplug the refrigator, remove everything from
frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws
remove motor bracket from rear panel 4 screws
unplug motor . replace motor and reasemble in
reverse order. the new motor is very quiet.