19784B Admiral Refrigerator - Instructions

All Instructions for the 19784B
106 - 120 of 536

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
fridge door switch did not work
2 of 2 people found this instruction helpful.
  • stu from richmond, VA
  • Easy
  • Less than 15 mins
  • Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Not making ice, and water leaking in freezer
2 of 2 people found this instruction helpful.
  • Raymond from Northglenn, CO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!
Was this helpful?
Thank you for voting!
Old ice maker started leaking
2 of 2 people found this instruction helpful.
  • Curtis from Barrington, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.
Was this helpful?
Thank you for voting!
Ice tray filled up with water. Stopped making ice.
2 of 2 people found this instruction helpful.
  • robert from COLDSPRING, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.
Was this helpful?
Thank you for voting!
Ice maker not working.
2 of 2 people found this instruction helpful.
  • kurt from Westminster, CO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a g uide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.
Was this helpful?
Thank you for voting!
Ice maker putting black pieces of plastic in the ice
2 of 2 people found this instruction helpful.
  • Doug from Lewisville, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Replaced ice ice maker using
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.
Was this helpful?
Thank you for voting!
Ice maker working with no production of ice
2 of 2 people found this instruction helpful.
  • Paul from East Northport, NY
  • Really Easy
  • 15 - 30 mins
  • Socket set, Wrench (Adjustable)
Turn off the water source and unplug freezer. Remove copper tube and then remove valve from back of refrigerator. Disconnect plastic tube and power connection. Mark power connection plug top with a "T", this reminder helps with the new valve. Plug power and plastic tube into new valve and screw assembly back into refrigerator. Using a wrench, connect copper tube into valve. Restore water source and plug back in in freezer. Within a couple hours, ice production was back.
Like the other repair stories (that helped me), this job was very easy.
Was this helpful?
Thank you for voting!
water leaking into ice tray, frozen glob of ice
2 of 2 people found this instruction helpful.
  • james from newfield, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers
installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.
Was this helpful?
Thank you for voting!
Icemaker made some pretty sad cubes! Hollow, unfilled, or small cubes
2 of 2 people found this instruction helpful.
  • Dana from ABINGTON, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.
Was this helpful?
Thank you for voting!
refrigerator was overheating, condensor fan dead.
2 of 3 people found this instruction helpful.
  • David from Granada Hills, CA
  • Really Easy
  • 15 - 30 mins
First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ,
reinstalled cover, plugged it in and BAM .WORKS PERF!
Was this helpful?
Thank you for voting!
Old Valve was dead
2 of 3 people found this instruction helpful.
  • Joseph from Bloomfield Hills, MI
  • Really Easy
  • 15 - 30 mins
  • Pliers
This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!
Was this helpful?
Thank you for voting!
Replaced Ice Maker
2 of 3 people found this instruction helpful.
  • Steven from Clinton Corners, NY
  • Easy
  • Less than 15 mins
  • Nutdriver
Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.
Was this helpful?
Thank you for voting!
icemaker quit working
2 of 3 people found this instruction helpful.
  • craig from green bay, WI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.
Was this helpful?
Thank you for voting!
Ice Maker Leaked Creating an Ice block
2 of 3 people found this instruction helpful.
  • Loren from Indianapolis, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people found this instruction helpful.
  • Gail from Golden, CO
  • Really Easy
  • Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
All Instructions for the 19784B
106 - 120 of 536